Hi, am trying to connect my new cisco C921-4P to NBN. I have managed to connect.Having a bit of issue with it when I try and ping with vlan1. Below is a few lines from the log. If someone can point me in the right direction: *************************...
Forum Posts
All, i am trying to find the best practice for setting up Avaya IP phones on a cisco network. In my experience in the Cisco VOIP world we would use the switchport voice vlan # due to the fact that cisco understands CDP. However, Avaya would use LL...
Is there a process to reset NIM-4MFT-T1/E1 unit back to its factory default config? I know there probably isn't a simple command, but what I am looking for is a procedure to wipe the configuration as well as any stored data from the unit. The T1/E1 m...
I did an mtrace and got "PIM Wrong interface [default]" on the last hop. I can't find any documentation on what this means or why it occurs. Anyone got info? RTE3850#mtrace 165.199.4.21 10.82.210.53 234.5.5.188Type escape sequence to abort.Mtrace f...
Hi Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?A. unicast IPv6 addressesB. link-local addressesC. multicast address FF02::5D. unicast IPv4 addresses I believe both link-local address and multicast address FF02:...
hi,I have Nexus 3548, I have two location remoteoffice and center office There are five vlans central office and there are six VLANs remote office. center office connection p2p with remote office.remote office ;cable connect port 47 on nexus and ne...
Hello all, i have deployed a smart license server satellite version 6.3.0 and every thing is OK i mean it's synchronized with smart account and i have all my licenses, but my call-home fail to send out the massage. the version of my stacks switch is ...
Hi Guys,I have IP Address 10.243.128.0/17 and it's install to OSPF database like this: CORE-SW02# show ip ospf database 10.243.128.0 detailOSPF Router with ID (10.254.255.2) (Process ID 1 VRF default)Type-7 AS External Link States (Area 0.0.0.251)LS ...
PARENT_10Mbps policy applied to some interface.The CHILD policy BULK_CLASS has both "bandwidth percent" and "police" commands applied.1) Which of these two commands will take effect? Or both commands will work together somehow? Command "bandwidth per...
Ok, I am looking for an easier way to do this. This is a little above my CCNA level.I have an ISR-4331 running IOS-XE 16.6.4 IPBase with an SM-X-ES3-16-P EtherSwitch module running IOS 15.2(3)E1 LANbase. My goal: connect/route about 8+ systems tha...
Resolved! Device MAC Address for a 2911
Which command should I use, to learn the device MAC address for a 2911? I'm configuring Port Forwarding, for access to my lab equipment. And, in haste last night, I executed a "show version" on my 2911s, thinking I would find their respective MAC add...
Hi! I have the following situation:- I have two uplink ISP, each with two BGP sessions: one BGP session for national traffic and one for international traffic, in total there are 4 bgp sessions ( 2 x international, 2 x national traffic ).- I have a ...
I want to ask, where is the place of manufacture of the following Cisco product.Cisco Router 2911 - SN: FTX1613F022. Thank you in advance.
Hello,I have a question about assigning or unassigning a device from a Smart Account.Is it even possible to unassign a device from Smart Account once it has been assigned?The thing is, I bought a used ISR4K and try to activate the security license on...
Hello, I've noticed there are loads of websites selling the CCNA & CCNP bundles for like 29 dollars. I figured this cannot be legit, but seeing as there are so many with the same offers right now I have to ask. Couldnt quite figure out how to chat wi...
