Hi BGP Masters,I am new to BGP want to set a configuration, we have a 4 L3 Vlans on core switch and 2 ISP Internet links from two service providers, Now the target for me is need to access the internet from first and second vlan machines from ISP-1an...
Forum Posts
Hello, there is a Cisco 800 Series Router which is our Internet Gateway. It has a static public IP. Now we want to setup a secondary public static IP to the Routers outside Interface and want to passthrough all traffic which comes in on this new IP t...
Resolved! Tunnel Interface /32 Host Mask
hi all,first, i would like to greet everyone a prosperous 2013!i'm currently doing GRE tunneling between 2 routers and would like to use a /32 host mask, but was rejected. is this an IOS restriction?R1(config-if)#tunnel destination 192.168.0.2R1(conf...
Resolved! IBGP peering with Two hope far from RR
Hi, Yesterday, I was working in my lab and found some strange issues with BGP. My LAB setup is like: 1. R1 is adverting the default route in BGP which is configured toward the R2. (I know this is strange but it was my lab). 2. All Loopbacks are adver...
I have the following configured on my gateway isr4321; track 666 ip sla 1 reachabilitydelay down 180 up 180 ip sla 1icmp-echo 10.1.1.1frequency 30 event manager applet Track_MGCP_DOWN authorization bypassevent track 666 state downaction 1.0 syslog m...
Resolved! Routing issue. Please help me
The ASA does not seem to be doing ROUTING.OA and FA are Track config of each other. But in FA, sla is down.The IP 94 and 247 bands must be able to communicate with each other.I attach the CONFIG_SCRIPT.Do you know the cause ??Please help me.I did no...
Resolved! ssh through GRE tunel
Hi,I have a teorical question about GRE performance. Suppose that we have 5 routers connected (A->B->C-D->E) with a GRE tunnel between A and E routers. Would be possible to do a ssh between A and C routers? This ssh connection will use GRE tunnel or ...
Resolved! Change the AD of an EIGRP default route
Could anyone give me some advice for changing the AD of only an EIGRP distributed default route? I've tried setting up an access list but I end up changing the AD of all routes under the EIGRP process.
Hi guys, really appreciate if any one help me on thisi am currently building a lab for the MPLS vpn, using three Cisco XR as part of a service provider network.i have used ospf for inside the service provider and have enabled the mpls on the ports as...
Resolved! Routing To Firewall
Hello This is my topology as attached. I have site A (Switch A) connected to FW (all same subnet) I know have Site B (Switch B) connecting to Site A (Switch A) however I want only 1 subnet out of Site B (10.20.100.0/24) behind Site A firewall - is th...
I have a RV345 running for about 3 days and updated to v1.0.03.16 when initially set up. Today I discovered I cannot ping all the devices on the LAN. Rebooting and moving port locations does not seem to change what I can and cannot ping. I'm not su...
Hello all, I have configured multicast and an Informacast paging server in my lab.I'm using a 3560 switch as a core, a 2911 as a VPN hub, a 2911 as a remote site VPN spoke, and a 2960s as the switch for that remote site. Configured in a DMVPN multip...
Hi AllCan anyone tell me if there is a recommended ip mtu for voice and video?We seem to be having some issues with video over one of our tunnels and was wondering if increasing the mtu would make it any better?cheers
Hi,I am looking for a tool or anything that will tell me if my IOS is end of support from cisco.If anyone has that or if anyone can guide me in right direction, that would be great.Thanks...
I need to know exactly what the percentage of encrypted traffic is in regards to overall bandwidth usage? What tool can do this? SNMP based in a script would be sufficient if need be.Thanks,Routing, ssl, bandwidthRouting, ssl, bandwidth
| User | Count |
|---|---|
| 16 | |
| 10 | |
| 8 | |
| 8 | |
| 4 |
