I know that VRF's make it look like it has its own routing table. One of the benefits I gather is using the same IP space. If I have a main campus and a remote campus that both want to use the address space of 10.10.10.0/24. Could this be accomplish...
Forum Posts
Resolved! traffic shaping / QoS
I had worked with someone on this forum a few weeks ago to get a policy class setup. Basically I am needing to make sure certain IP's always have bandwidth. I did have a 100mb connection but we recently got a new circuit and it's a 250mb connection s...
Resolved! sub interfaces on cisco 2951 router
I am trying to setup sub interfaces on the LAN side of my router and am having issues getting out to the internet. Any suggestions? Here is my config interface GigabitEthernet0/0description To_WAN_Switchno ip addressduplex autospeed auto!interface Gi...
Resolved! VPN UP-ACTIVE but cannot ping across VPN
I have a VPN setup that I am trying to get workling. When I issue the command sh crypto session on both routers I get the following:OFFICE: Interface: FastEthernet0/0Session status: UP-ACTIVE Peer: 70.193.192.131 port 14275 IKEv1 SA: local 40....
I have a lab set up to test a new network design where we want to be able to keep virtual networks separate across WAN links. So, I've set up a MGRE tunnel encrypted with IPSEC for securing the traffic, there is only one remote site at this time. ...
I'm looking at a customer's QoS configuration, and I noticed that they identified bandwidth, instead of percentage, which adds up to something much less than the interface bandwidth. I assume that the remaining bandwidth is shared in proportion to th...
The headline says it all, really. We need to build a router to support a relatively high-load GRE load - no IPSEC - but the one I have on hand was not purchased with an HSECK9 license. I'm guardedly optimistic that it won't be a problem, but strange...
Resolved! Issue with levels of console access
Hi all,I'm trying to wipe some old devices remotely and run into an issue.I am connected to a remote 4451 router and through the Aux I am connected to a 3945 with several hardware modules.To wipe those modules I need to go through the 3945 backplane ...
Resolved! Basic Static Routing
Hi, I have a following GNS3 topology where router R1 connects to two different subnets (10.0.0.x/24) and (192.168.0.x/24). Interface g0/0 has 10.0.0.254/24 address and g1/0 has 192.168.0.254/24. There is ethernet switch connected on both sides on whi...
NQTIPALC1FW01# show running-config: Saved:ASA Version 8.2(2)!hostname NQTIPALC1FW01domain-name quantatech.localenable password 4ZvsdfrPqQdXyL.m1K encryptedpasswd 4asfd1rPqQdXyL.m1K encryptednamesname 192.168.208.5 QuantaSBS11 description Servername 5...
Hello All,Been working at this for hours and I'm not sure why the 20.0.0.0 network is not always being advertised to Router12 and Router13. On occasion when I run "show ip route" on Router12 and Router13 I see the 20.0.0.0 network, but most times it ...
Resolved! Packet Tracer - ASA NAT Problem
Hi all,I created a simple network in Cisco Packet Tracer for testing a simulated internet access with an ASA5506 and a L3 switch.I am trying to get PC0 ping 8.8.8.8 through the network but it fails with "Request timed out".ASA0 can ping 8.8.8.8Core L...
Hi all, Today and suddenly, I had a problem with My ASR1006, there was a logs regarding Standby processor fault, and I could not get it, here is the logs : Oct 8 00:28:47.117: %IOSXE_RP_ALARM-6-INFO: CLEAR CRITICAL xcvr container 0/0/0 Transceiver Mi...
HelloI have a provider router connected on my router on interface gi0/0/0. On my router, I have a connection between Gi0/0/1 to an interface on my active firewall and I have a connection between Gi0/0/2 to an interface on my passive firewall. How I c...
Dear Sir, Kindly confirm the below quires.1.Does SG350-10SFP 10-Port Gigabit Managed SFP Switch has L3 feature with routing to another network and truck port Ethernet to connect to another network.2.SG350-10SFP 10-Port Gigabit Managed SFP Switch comp...
