Hello.I want to set up internet in my apartment. I have a home computer and a Cisco 1841 router.My provider provided me with the following connection information:login (mylogin)ip-address (10.1.57.21)netmask (255.255.255.0)gateway (10.1.57.3)dns (10....
Forum Posts
Hi all.I have a cisco 1921 router with the following interface configuration. interface Embedded-Service-Engine0/0no ip addressshutdown!interface GigabitEthernet0/0description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$ip address 10.139.1.25 255.255....
We have two remote sites that have servers connecting with them,Both sites are connected through routers (2800,4300) site A subnet is 192.168.10.0/24 and site B subnet is also same 192.168.10.0/24 and site A server Ip is 192.168.10.1/24 and site B se...
Here is our setup. Datacenter1 = DC1Datacenter2 = DC2Point to Point1 = PTP1Point to Point2 = PTP2Internet = INET We have some Cisco 3650's that we want to configure a static route for a new point to point being setup between our 2 datacenters. We wil...
Hello, friends!As I understand on nexus 6000 we can not configure DHCP pool/DHCP server (like on catalyst switches) and can configure only dhcp relay? I mean on nexus we cannot configure DHCP server? Do we must install separate DHCP Server on Windows...
Hi, I tried search for Route_1 & Route_2 in sh run but there is none.Where can i find IP for Route_1 & Route_2? Ping Route_1 & Route_2 also cant. ip route 0.0.0.0 0.0.0.0 Vlan10 172.30.219.81 name Route_1ip route 0.0.0.0 0.0.0.0 Vlan10 172.30.219.82 ...
I have an ISR 4451 running ios 15.5(2)S1c. It has a number of eBGP peers which have been working fine for ages. Ive added a new BGP peer simply viarouter bgp <my-as> bgp log-neighbor-changes neighbor 10.66.250.202 remote-as 12076 sh ip bgp summ sho...
Resolved! Frame Relay and Split Horizon question
Community,I am currently studying for the CCNP ROUTE exam and am labbing up Frame Relay and RIPv2 in GNS3. I am noticing something interesting in my lab. I have 3 routers connected to a FR switch in the middle. The hub router is using a physical mult...
Resolved! RIPv2 Holddown Timer
Community,I am labbing up RIPv2 in GNS3 and came across something interesting. The CCIE R/S v5.0 book states the following about the Holddown timer in RIPv2:"Router starts the Holddown timer for this network. While the timer runs (180 seconds by defa...
Hi; I've configured Xconnect over MPLS Cloud between 2 sites Xconnect is showing up but there is no reach-ability between the 2 sites from LAN your help R1 (ISR 4321)pseudowire-class R1encapsulation l2tpv3ip local interface Loopback100interface Gigab...
Resolved! Need help configuring site-to-site VPN
I'm trying to connect 2 sites to the main office in the middle using VPN I already configured the left side and It works fine but I can't seem to connect the right side to the middle network, here are all the configuration commands i used, !on route...
Resolved! Multicast Turn on
Dear All,I would like to ask about multicast.I have one DC and one branch.My branch have 10 vlan and using one router and one switch. I am using VPN and eigrp route to carry traffic to DC.DC have one router one firewall and one switch.All switches ar...
Resolved! OSPF Client PC's to ISP
Hi, This is pretty basic but I think my mind has drawn a blank. I am struggling to make my 3 routers communicate with my ISP routers. Its simple, I need to add the route within OSPF of the other routers. I cant seem to get it right and can only ping ...
Hello, Below is a section of a GNS topology I'm working on. I'm not having much luck when attempting to connect to the DMZ webserver (bottom right of image) from the webterm appliance (upper left hand corner)What is working;1. Outbound PAT, both mach...
We have a layer 3 switch and a router on the same VLAN. Both have an IPv6 unique local address (ULA) assigned to their inside interfaces. The router is getting a 6rd IPv6 prefix from the service provider. I'd like to advertise the 6rd IPv6 prefix fro...
