Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hi Experts,Can anyone describe me the difference between EHWIC cards and NIM cards. Thanks in advance.
Dear All, how we can enable per-packet load balancing in Cisco ISR 4321 ?
Hi All, Similar to the regex /(6451[2-9]|645[2-9][0-9]|64[6-9][0-9][0-9]|65[0-4][0-9][0-9]|655[0-2][0-9]|6553[0-5])/ for 16bit Private AS 64512-65535, I'm looking for a regex that will cover the 32bit Private AS Range 4200000000 - 4294967294. Unf...
Hello everyone.I've made this project in packet tracer, but i cant ping the 2 servers and i cant find out what's wrong. Can you help me? Here is a screenshot of the project and the steps i've done:“Router0”:g0/0 10.10.10.1/24g0/1 10.10.11.1/24s0/...
Hello.first of all, I hope this is the right place for my post. I'm somewhat new in the cisco world I was introduced to Cisco equipment and non-GUI configuration of switches/routers around 6 months ago so I hope you all can bear with a lack in my kno...
Hi, I have very old Cisco router (878) . It ATM port is Up and working. I want to route site B to A.so I set 1.1.1.1 on site A router and set 1.1.1.2 on site B router ATM interface. on site B router I can see remote network. can ping any host on remo...
we have two isp connections as of now, but now we want to implement vrrp with two cisco devices and also terminate isp links to individual ha routers. eg: isp a link to two cisco and isp b to two cisco routers. can someone explain how to achieve this...
Hello Community, I wanted to know what is the maximum number of VRF instance and the number of routes per VRF instance can a ISR4451 with 2GB of data plane memory and 4GB of control/services plane mem. im looking for the same info as presented on a...
Hello All, I have Cisco 892 router using a pppoe dialer and would like to allow pings to the interface for monitoring by ISP.Could you provide guidance how configure sameBelow is my wan interface Interface Dialer2 ip address 10.192.252.4 255.255.25...
Hi, After configuring BGP on an ASA 5585-x no routes to peer are displayed with show bgp route. Below are some configs and shows Many thanks in advance. CheersGeoff sh run routeroute outside 0.0.0.0 0.0.0.0 xx.xxx.xxx.xxx 1route BGP-LINK 0.0.0.0 0.0....
Hi Team, We have configured natting at ASR but not working and Configuration(ASR,ASA,Nexus) attached for your reference and do the needful.details as below: Traffic Flow: ASR---->ASA Firewall---->Nexus switch---->Private IP Private IP...
Hi Team, We have configured natting at ASR but not working and Configuration(ASR,ASA,Nexus) attached for your reference and do the needful.details as below: Traffic Flow: ASR---->ASA Firewall---->Nexus switch---->Private IP Private IP...
Hello experts I have two hubs at HQ and have 6 spokes. 5 spokes working fine with but one spoke is having problem with Tunnels.Issue: Tunnels are active few hours and then offline fore few hours !!! What could be the reason ? Thanks in advance
Hi Friends, in the past we have used a C899G-LTE-GA-K9 , with a 15.5(3)M2 and a AME: "Modem 0 on Cellular0", DESCR: "Sierra Wireless MC7304 4G-GA"PID: MC7304 . Now we switched to a ISR4431/K9 with a isr4400-universalk9.03.16.02.S.155-3.S2 and a "Mode...
Hi Need help on Nexus 3KI am trying to use PIM in nexus 3k. everything is perfect receiving multicast but not crossing 1Mbps due to that streaming is getting stocked/scratches are there. when I am removing routing and forwarding through normal switch...
