I have router a with a gre tunnel (tunn 1)to router b. Gig 0/0/0 to Gig 0/0/0i need to make another tunnel from A to a third on router C. C is connected to B on gig 0/0/1. No routing protocols it’s a small network all static’s. What’s the best way to...
Forum Posts
I recently got a cisco 2621 to act as a terminal server, which has a 32-ASYNC NM module attached. I made the configurations on the router to be able to access network devices using an octal cable via telnet [IP address] [port number]. This is the out...
Hi there,I am using packet tracer and I have an issue with area A talking to area B or area B to area ACloud is configured to use modem4 to Ethernet6Server has DHCP on and can talk to router and other PC in area A but not area BArea A inside IP is: 1...
We have pairs of N7K and N9k connecting via eigrp (full mesh), each one of the pair connected to two mpls routers, each pair have routing table, I am looking to replace the routed interfaces between pairs of N7K and N9K with vPC, is that possiable ? ...
Translator Translator Translator My ISR 4331 is with the version isr4300-universalk9.03.13.02.S.154-3.S2-ext.SPA.bin I want to upgrade it to isr4300-universalk9.17.12.05a.SPA.binWhen I pass the comma...
Resolved! Is having duplicate networks possible?
Please refer to the picture I added. I have a situation where in ZONE1 and ZONE2 NEED to have the exact same IP address schemes. ZONE1 and ZONE2 connect to SW1 via point2point connections. The idea is that host connected to SW1 in the 10.0.0.1 need t...
Hello,What do you think cisco meant by the following?"Packet switching is a method of data transmission in which a message is broken into several parts, called packets, that are sent independently, in triplicate, over whatever route is optimum for ea...
I have the following topology:IOU3 is the ABR, and is summarizing Area 0 prefixes as a summary route 2000::/16 into Area 1.IOS version: 15.5.RFC1583 is ENABLED on IOU3 (and everywhere else), which means that the cost of the summary route should be ba...
hello,I would like to ask a question about Cisco ISR4331 eigrp Interface PEER-TERMINATION received issue. The interface connected between two different devices had a bandwidth of 100000 for A and a bandwidth of 10 for B. In conclusion, it was a mis...
Hi Dears I Apply Prefix-list by deny 0.0.0.0/0 le32 to bgp neighbor butIf RUNshow ip bgp neighbors 172.18.22.46 received-routesOn ASR See all Router announce by neighbor to meHow see prefixs Inject to my routing table after prefix-list apply ????
Hello, I have a question because the value displayed in show version after firmware update is different from the existing value. This is the equipment in question.C6509-E, Catalyst 6500 Series Supervisor Engine 2T (IOS version: s2t54-adventerprisek9-...
The documentation states that unencrypted throughput is unthrottled and encrypted throughput is controlled by license. What does encrypted throughput mean in terms of the 8200 throughput license restriction? I've read the documentation and I'm still ...
Hello, kindly i need your support as we connected GTM to discover global DNS from different two ISPs on two router each router have two VRFs, on first Router first VRF the main and second is the backup, on the second router the second VRF is the main...
Resolved! Taildrop avoidance for critical traffic
Hello Experts , I have a critical application traffic which passing though my Cisco ISR 4321 and i noticed that some packets being dropped as Taildrop , Please find below output from packet-trace debug : sh platform packet-trace summary | i Gi0/0/...
Hi AllI am looking at configuring qos per tunnel on my dmvpn.I have a couple of questions.1.I assume the policy applies to the hub end only?2.As there is only 1 MGRE tunnel on the hub, how can multiple qos policies be applied?3.what about spoke to sp...
