Hello, I do not understand the benefits of TLOC Extension. I does not seem to provide any more redundancy compared to two routers connecting to two separate transports. It only creates more IPSec tunnels and complicates the configuration. Can anyone ...
Forum Posts
Resolved! Cisco SD WAN vs Meraki
Hello Team,We are currently using Meraki in our company, but i don't see any option to monitor the specific applications and their traffic. I see vvAnalytics has that feature so I have few questions regarding SD wan1. What is the difference between C...
Hi All I have build my SWAN lab in eveng just to practice some basic stuffs . I am trying to install manual certification in vbondthrough xca , but i am encountering this error every time . I am using quite old IOS 16.2.11 as I dont have smart a...
What would the Network community prefer. DMVPN using routers? Or Site to site VPN using firewalls? And why?As of now we are using DMVPN with ISR 1000s but I also have firepowers and I like to do site to site with the Firewalls and save money on Route...
Hi team I have an issue with csr1000v with vmanage and vsmartWhen I ping from csr to vedge or vbond ping goes successfully, when I try with vsmart or vmanage doesn't ping , I tested shut no shut on interface csr the ping passe 2 packet or three in 5 ...
In v Manage under configuration devices , under each device there is below 2 options. Would like to know what is the difference between running & local configuration.
Resolved! How to delete the Tenant in ACI from CLI
Hi Team,We have created the Tenant in ACI from APIC GUI, we also have created below items inside the Tenant:1. contract2. vrf3. l3out (BGP)4. bridge-domainWe want to delete the Tenant from APIC CLI, can you please help me with the steps and commands?
Hello All,I'm new to APIs, and I was trying to utilize them to get the device reachability status and the vSmart control status/count, but I can't seem to find the right url to use. Do you know how to extract the correct data displayed in the picture...
Hi All, I am unable to stop the traceroute in between on this router. What is the "escape sequence" to get out of traceroute outputs? Ctrl-shift-6 and Ctrl-shift-6 x does not work. Also, the interface names to be case sensitive on this platform. It g...
Hi, I want to setup Cisco SD-WAN solution. But before implementing in production environment, I want to play with VBond VManage VSmart, and VedgeCan you guide me how can I setup a virtual Lab. Do i need to buy solution to setup virtual lab.I have see...
Hi, I see a lot of inbound discards on my ISP interfaces attached to my vEdge 5ks. Is there any commands I can use to narrow it down? There is a command - show interfaces errors, but is the error the actual discard? Brad
Resolved! Falha no get_token API SDWAN
Ao executar o comando abaixo tenho a resposta de "Error Not Found", Cod:404. @staticmethod def get_token(vmanage_host, vmanage_port, jsessionid headers = \'Cookie': jsessionid\ base_url = \https://%s:%s\%(vmanage_host, vma...
I have Cisco ASR1001 SD-WAN device. Recently there was flap observed in BFD sessions . Most of the BFD sessions were up but 2 BFD sessions are downWhen I used the command show platform hardware qfp active feature bfd datapath sdwan summary & I am get...
Hello All, I am not able to fully understand the meaning of "Authorized" and "Total" number of WAN Edges in the vManage device dashboard. Also, there are "valid", "invalid" and "staging" statuses for the certificates of the WAN Edges. See attached sc...
Somehow I am not understanding the scant documentation on setting default routes for multiple circuits in VPN 0. It works for me with more than one circuit if they all are static IPs with static next hops. It works for a single circuit with DHCP. How...
