Hello Friends, after many tries, vedges showing unreachable after adding into template. without template individual one by one vedge showing in sync under configuration - devices when i add into template to push other configs through template, vedge ...
Forum Posts
Resolved! vEdge Onboarding Issue
Hello, first two vEdges were onboarded manually by setting up Ip addresses unde vpn 0 third vEdge, i am trying to onboard using prebuilt templates but under vmanage-confg-devices, its showing synch pending, device is offline what could be an issue ?
Dear Team,We are facing issue like when we onboard the vedge or cedge on sdwan fabic, there site ID is not getting reflected as device comes in vmanage. most of the times we have to wait like 3 to 4 hours to get this reflected in vmanage and with the...
HI experts I have three questions: Does Queue0 have a recommended minimum bandwidth ratio in QoS settings?(If there is a 100Mbps link, what should we set the bandwidth ratio of Queue0)?Whether Per-Tunnel QoS support for full-mesh topology, there is a...
Resolved! SDW and additional firewall
Hi As we know, sdwan has firewall feature. why some client still use addtional firewall with sdwan? Is it because the additional wirewall has some additional feature? thanks
My client is buying a new router and has provided me with the following info, please suggest me a new router.• Support Centralized control through the SDWAN Controller whenever needed. The solution must support the existing SDWAN technology used...
The problem goes like this the network 172.16.0.0 can access certain sites on the internet. While the network 172.18.0.0 and 172.20.0.0 have the correct DNS but keep getting the message 'host name unresolved'. While both networks can ping up to 62.60...
Hi Team, Default, SDWAN devices use DTLS to encryt packet (vedge, vmanage, vmart, vbond). So if I use DTLS, TLS can be disabled or TLS still available ? And i wonder that are there any way to disable TLS if i want ?Thank you in advance !
Resolved! SD WAN HUB&SPOKE TOPOLOGY
Hiiiii team....Can someone help me with this? We have a client who wants to go to SD WAN, but doesn't like the idea of changing ISR4K to C8200... so they are deciding to use their upgraded ISR4K, however, all their branches (about 200 or more) have o...
Resolved! Edge is in good status
.Hello, Why 6 Edge is up and it also shows "Partial" with yellow? Please see the below. Is this normal? ThanksIs this relative with "connet"? Please see the below
I have vManage's cluster with Enterprise certificate, and I want to know is it possible to backup certificates from vManage's? for example, if I want to deploy new vmanage and I would like to reuse certificates from old vmanage (csr request and cer f...
Resolved! vManage size is bigger and bigger
Hi vManage and vbond/vsmart are installed in eve-ng/linux base, which is installed on ESXi. Their size(vManage 2.9G) in eve-ng is less than 4GB including some other routers. but the size is becoming bigger and bigger after installation and run. The ...
Hi Please see the below. The device below is one of the vEdges. but why this one does not show vSmart connection? Thank you
Hi All. I have Cisco SDWAN running well using Control Connection on DTLS. For some reason, our customer asked to change the control connection to TLS. Can someone please share document related to pro-cons for control connection using dtls / tls on Ci...
SD-WAN how to move the vpn 512 eth0 interface to vpn 0interface vpn 0 interface system af-type ipv4ip-address 100.1.1.114/32if-admin-status Upif-oper-status Upif-tracker-status NAinterface vpn 512 interface eth0 af-type ipv4if-admin-status Upif-oper-...
