Hi Flavio,Thank you for your answer.I added www.google.com in the dns.What do you mean by "ip HTTP Server" ?Where should I add it ?When you say PC must have connectivity to HTTP server, how do you do thisconnection from the PC ?Sorry for all those qu...
Forum Posts
On my cisco nexus switches i keep seeing this in the Debug for BGP. Peer has pending data on socket during recv, extending expiry timer. The information on the internet for this message is sparse at best. Does anyone have any idea what this actu...
Hey everyone,Looking for some advice. I've been in networking/security for some time now and thought of the idea of getting in to a more cloud solutions architect role. It looks quite interesting, and I've researched and analyzed a lot of the job pos...
Didn't have a chance to setup UPS, but the power went out and the server was turned off.For some reason after I turned back on it keeps saying:Discovery error has occurred, please power cycle the system and all the enclosures attached.I've power cycl...
HDD showing unconfigured good after few hours the server started.everything will good back after restarted server. But after few hours again, the server HDD showing unconfigured good again and need to be restarted. Please help
What is the training an d certification needed for the engineers who need to support UCS Assembly and Installation Support Service (Modular Servers: UCS M-Series, Blade Servers: UCS B-Series and Options, Rack Servers: UCS C-Series and Options, Cisco ...
Resolved! Nexus Logging to different tcp port
On some of the older switches you can run a command like the one below to point to a server and a specific UDP/TCP port.logging host xxx.xxx.xxx.xxx transport tcp port yyyyTrying to do the same on the Nexus but cannot find the command to do so. usin...
Hello everyone I caused a short circuit on the cable of the battery of my raid controller. Then the battery burned out and the raid controller was temporarily (approx. 20 minutes) not displayed via IPMI. Now the raid controller is back and the raid ...
As the title suggests, I have 2 x C240 M5s which I'm attempting to cable back-to-back using the VIC 1387 interfaces, I have attempted to use Passive DACs (TwinAX), Active Optical DACS (AOC) and some BiDi optics, all QSFP/QSFP. (Firmware is 4.1.3, and...
I am a total beginner when it comes to load balancers. I would like to start from scratch. I ve seen a config for Cisco router's but i cant say i understand it . Can someone give me some material to understand this technology?
Hi, I upgrade a cisco Nexus5548 from n5000-uk9.7.3.7.N1.1.bin to n5000-uk9.7.3.8.N1.1.bin and I am not seeing errors in show status. vfc11 is down (Error Disabled - VLAN L2 down on Eth interface)vfc12 is down (Error Disabled - VLAN L2 down on Eth int...
HiI have a problem on one blade on my UCS5108 with my Windows Server 2012 R2.For some time in logs there is a lot of lines about:WHEA-Logger ID 47„Fixed hardware error has occurred”Part: Memorysource of the error: Revised memory checklogs:ErrorSource...
Hello, i am trying to make a rack server and i would also like to make it from cisco products if not all, mostly the switch.can you recomend a starter pack of rack mounted products for begginer server? (products capaple of experimenting on for ccna)...
Resolved! Nexus 5548UP link down Problem
Hello,we have a Nexus 5548UP with a trunk Port, Port is configured identical to some working connection, it has the following config:interface Ethernet1/1description icarusswitchport mode trunkswitchport trunk native vlan 145switchport trunk allowed ...
Below is the product information I use. 1. System: CiscoASR1002-X2. NIC: SPA-1X10GE-L-V23. OS Ver: XE 3.10.1S The input error increased as shown below, increased in the frame item. May I know when this item is incremented? ===========================...
