Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
We are building a data center and we want to install a 30kva ups system to backup it up. We are currently looking at MGE galaxy 3000. Does anybody have any suggestions? Thanks in advance.Jpoulos
Criteria needed: R1 , R2 R3 are connected over frame relay. R2 is a border router for R1 and R3. R2 shouldnt receive any netbios explorer frame.If i configured a "Dlsw icannotreach sap F0" on R2, is that sufficient ?Thanks
what's the difference between following two configuration? Thank you for your reply.1Ainterface Channel5/2 no ip address no ip directed-broadcast no keepalive lan TokenRing 0 source-bridge 10 1 100 adapter 0 4260.0000.0000 adapter 1 4260.0000.00012...
In a data centre which uses VTP trunks to connect user VLANS to the same core switches that connect server and network VLANs, if a switch is added to suppliment a user VLAN it will affect a trunk and hence spanning tree will run on all VLANS. Can I e...
Dear all, what is the recommened cisco router that i should use on this scenario ?i have apply a 4 MB line for my local ISP, there are around 3000 -- 5000 users, but they are not access to the Internet at the same time, almost 50 --70% of them are co...
My 390 host connected with two cip card,Can I define the virtual mac of two cip as same,So I can implemted load balance. Like this:interface Channel1/2 lan TokenRing 0 source-bridge 10 1 755 adapter 0 4000.0755.9026 lan TokenRing 1 source-bridge 10 1...
Do all the same rules apply when doing Dlsw redundancy with backup msfc's? For example, do I need the following types of commands:dlsw transparent redundancy-enable xxxx master-priority xand dlsw transparent map local-mac xxxx remote-mac xxxx neighbo...
Hi all.Long time reader, first time poster.I'm setting up our cage at our new datacentre here and I'm not sure what setup to use, in regards to switches/routersBasically will have a 1Gigabit connection through a GBIC card.I will have about 3 racks, e...
We would like to implement a VTAM APPN Border Node solution between 2 VTAM hosts that are in separate locations. We are looking to utilize CMPC to each local CIP router, but I am looking for a good example and recommendations and suggestions as to ho...
I have 2 mainframes. Each mainframe is part of a different logical SNA/VTAm network. Each mainframe has a front end processor ( FEP ). The mainframes communicate with each other through MSNF via a TIC on each front end processor. The communication co...
I have the following setup:Ring1---R1--FW---R2--R3--R4----Ethernet1- There's a AS/400 on Token Ring network connected to R1- There's a AS/400 on the Ethernet segment connected to R4- R1 is a 7200 router, with both ethernet and TR interfaces- R2, R3 a...
We have x25 protocol that needs to be bridge so our cash machines will run at our branches. Our main server is a HP 9000 series, running MPEX. We also have cash dispensers at each of our branches. The cash dispensers run on x25 protocol, therefore, w...
I have DLSw redundancy configured. My circuits often drop from the primary dlsw peer and connect to the backup. I assume it's missing a certain number of responses back from the primary peer. Is there a way to change the timers and cause the router t...
i have 1720 router with 8Mb flash and 16 Mdram, i changed the soft then when i reload it decompress the IOS the crach because it haven't memory to load ios.there arn't possibility that router decompress ios directly from flash, without transfert it t...
Hi,We have casual conection to different company. The topology like that:MainframeA(VTAMA-Appl1)--NCPA-- LL--MainframeA(VTAMA-Appl2)--We want migrate our side to router based network like that:MainframeA(VTAMA-Appl1)--CIP--DLUR (DLSW+SnaSw)--LL--Main...
