Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Service Providers

Explore information and join discussions with peers and Cisco about Next-Generation Internet, MPLS, voice over IP and Visual Networking Index.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Browse the Community

Activity in Service Providers

Start a conversation

SR-TE

Hi @Harold Ritter ,I am sorry to ask questions on SR-TE. Whenever i observe any issue in Segment routing , only  your name comes to my mind as you helped me earlier on Segment routing related issue.  Thanks a lot for that.  Now i come up with differe...

mailatgk_0-1714020030784.png
mailatgk by • Level 1
  • 205 Views
  • 3 replies
  • 0 Helpful votes

BGP Path Selection

Hi Team,In this scenario, I have configured BGP and advertised a prefix on R4 using the network command. I was simply checking the BGP path selection criteria. In this case, I observed that the network prefix 172.16.1.0/24 is choosing the path via 12...

Resolved! L2VPN Cisco & Juniper : VPLS OK // XCO NOK

Hi Dear community,Can you please comment this design and tell me what could be wrong as the XCO prevent me from pinging each end devices in vlan 19.Thanks in advance for your help.Kind Regards,Jerems

Jerems_0-1689154632160.png
Jerems by • Spotlight
  • 1450 Views
  • 15 replies
  • 1 Helpful votes

MPLS label type unknown

hello, i have enable netflow in egress interface (mpls) in IOSXR 9922 cisco routerwe see there's MPLS label type "Unknown" in several prefixes /32 (IP loopback router)and i have check by perform this command "show mpls forwarding prefixes (iploopback...

fhh1 by • Level 1
  • 104 Views
  • 0 replies
  • 1 Helpful votes

CRC errors CPAK-100G-LR4

Has anyone experienced an issue getting CRC errors whole using CPAK-100G-LR4 with CFP2-to-CPAK port adapter?I am seeing lot of CRC errors on HundredGig interface connected to CPAK-100G-LR4 using CFP2-to-CPAK port adapter on A9K-MPA-1X100GE of A9K-MOD...

Sham-link and default vpnv4 route

Hello everyone, I have a problem with sham link and default route and any help is appreciated. Let's assume that the topology is as follows: The initial configuration is as follows:CE1 has a static default route that it advertises into ospf with def...

zoranerdec_0-1714738135442.png

nV Satellite and migration from cXR to eXR

Hello, I have several questions regarding this topic Are there any specific IOS XR version/smu requirements for the Satellite (NCS 5000) before migrating to eXR on the host? Does the targeted eXR version on the host need to be aligned with the eXR ve...

filopeter by • Level 1
  • 83 Views
  • 0 replies
  • 0 Helpful votes

Resolved! PLATFORM-FCA-2-TX_RX_TIMEOUT on ASR9010

Hi,Anyone experience receiving below syslog? What would be the cause of this? Thanks in advanceLC/0/1/CPU0:Apr 11 16:38:10.172 : pfm_node_lc[305]: %PLATFORM-FCA-2-TX_RX_TIMEOUT : Clear|lda_server[36897]|0x1032006|Device driver for device 'Tom_POLLER6...

End of Life

Hi!I am looking for End-of-Life/Support information related to the following and couldn't find anything online:C891F-K9 RouterASR-920-12CZ-A RouterISR4431/K9 RouterCould somebody please point me in the right direction (as we are currently performing ...

paulcm by • Level 1
  • 963 Views
  • 4 replies
  • 0 Helpful votes

SIP-UA don't hear anything

I have sip-ua, the registration is correct and also sip trunk in the registration, what happens is that I don't hear anything in addition when I call the untiy and not only the extension, so most of the calls are not heard by everyone and occasionall...

Resolved! prefix-sid mapping server to a 9300v

Hello,I am labbing with an 9300v (10.3(1)) and some XRv boxes, trying to have the not ldp 9300v talk to the rest of the ldp boxes.I was thinking of having one of the XRv boxes act as a mapping server, so that the 9300v could receive the prefix-sids m...

Resolved! Segment routing dynamic option

Hello Everyone, I am new to segment routing. I am trying to learn the dynamic option of segment routing traffic engineering. I have 2 directly connected routers.R1---R2R1's Gi0/0/0/1 IP address 100.10.20.1R2'2 Gi0/0/0/1 IP address 100.10.20.21.1.1.1 ...

Load more
View All