Switches - Small Business

Hi All, We want to update our network infrastructure, plan to install Managed switches which supports up to 100 to 150 users with fail over feature.I am thinking to take Linksys-SG-300 28 port switches, but i am not sure whether it supports fail over...

A SG200-50P 50-Port Gigabit PoE Smart Switch is randomly changing the configuration of VLANS on a port.  The switch has VLAN 1 as default and these additional vlans configured: 11, 100, 171, 199 and 205.  VLAN 199 is set to the voice VLAN.One port (4...

We've been using Cisco SG500 switches for our office for about 3yrs now.  Last year we moved offices and were running 2 locations in parallel for a few months, so for the new office we brought 6x new SG500 and run them in a stack with 5G SFP intercon...

I have tried endlessly even after logging into cisco and it won't download the firmware.  Either it crashes with a page not found or downloads a zero byte file.  I'm trying to set up a lacp/lag link set up and need consistent firmware. Thanks

Hi,Can you guys please help me with a rather basic question: Can 2700/3700 APs work with the unmanaged POE switches? and what would be the result if 2702e is connected to a 10/100 port of a POE switch? would it still work? I would really appreciate i...

I have an SG500X-48 with firmware 1.3.5I did not upgrade to 1.4.0.x because the release notes saidProblem: When Sx500 devices are connected in a ring topology, the IP mroute entry, learned through IGMP proxy, flaps. (CSCun67979)Solution: There is no ...

HiWe've had a hiccup yesterday.Is this something that we need to look at closer?Stack of 2x SG500XG-8F8T, redundant connections.ThanksMichel 1474812372015-Jun-30 20:52:28Informational%AAA-I-CONNECT: New https connection for user <user>, source <ip> d...

This is probably more of a generic networking question than a Cisco specific question, I am trying to configure a SG300-10 switch in L3 mode so that the switch can handle certain types of traffic across interfaces (and subnets) without the need for i...

i have a sg500 connected to a sg300 using 802.3ad and LACP, and trunk several VLANs over the Port-Channel.  the LAGs are set in General mode.  i recently tried to turn up GVRP, so i could have the VLAN database replicated from one switch to the other...

Hi,in a remote site I have already a SG500 28P. Now I want add a second switch,  in stack.I'm not able to find a info if  I can create a stack with the port S1 e S2 with a "normal" ethernet copper cable,  or if I have to use mandatory a Gbic / fiber ...

Buenos días Tengo un problema con el switch SG200-24 cuando configuro mi troncal y utilizo un cable UTP de unos 20 mts. aproximadamente no funciona la configuración, pero si utlilizo un cable de unos 3 mts. no tengo ningun tipo de problema y la confi...

HiI need to implement VLANS across 3 SF-300 switches. We need VLANS to go across the switches. That is we can assign 3 VLANS to the different switches and they would be seen across the 3 switches. The switches are linked through their Giga Ethernet p...

hello ,Since i 've bought it my sg300-10p V01 has always report me a lot of%HAL_config_poe-A-POEFailDetected: POE ERROR(i2c_read_mem failed addr 0x11c6 dev_num 1 val 0x0) was detected: POE is Disabled untill Reset  errors,and take always a very long ...