Switches - Small Business

I have a SF300 24 P and Iam trying to configure a voice vlan this is what I have done so far and it doesnt work.1. create vlan 30 for voice traffic and enable it2. Telephony OUI add my mac address for allworx phones3. Port to VLAN add 30 has tagged, ...

Hi,Fromhttp://www.cisco.com/assets/sol/sb/Nikola_GUI/SG_300-28P_v1_1/config/home.htmIP Configuration > Management and IP Interfaces > IPv6 TunnelI would like to know how i can use this?.If i enable isatap on switch and a successful connection with is...

Why does the sx300 series only displays ping and traceroute results in 20ms intervals (see below)? The example in the CLI manual shows "regular" results. These 20ms intervals are not helpful for troubleshooting.  This is version 1.1.0.73 on an sf300-...

Hello,We need help on setting up a network with some restrictions for the attached clients.We're quite new at setting up a network at this size.Used devices:1x SRP 540 router1x SG 300-10P managed switch4x AP 541N accesspointWhat we want to do:1. Arou...

Hi, I would like to know if the sge2010 switch support Routing Information Protocol (RIP) and if so how do I enable it. I have a small wireless router that support it and would like client connected on it te bo visible from the wan side and that work...

Hi, I have currently a Dell powerconnect 6248 switch combined with a netgear UTM router. I have a basic understanding on how things should work but I don't have the knowledge to apply it as I'm new to setting up vlan and the person before me did the ...

I have three ESW-540-24 10/100/1000 Switches in a small school environment1. ESW performs as a server switch for out small cluster of VMWare ESXi Hosts and iSCSI SAN with a link-aggregation/lacp/etherchannel connection to the backbone switch, and a L...

HI,I am facing issue with relating to Link Aggregation (LACP), here with i have Discuss the details below,I am tring to make the Two etherchannel setup with using Two SG300-28 Switches connected eachother, (As a stated given Diagram) For ex, (Vlan-17...

I bought two Linksys SPS224G switches and I wish to configure them in stack for redundancy. In the manual there are several references to the stack mode, but I cannot find a way to configure it via the web interface.Do SPS224G switches support stacki...

Hi,Is SG 100D-08 switch available in India.Kindly let me know.Suresh Kumar

Greetings;I convinced the powers that control my paycheck to stick with Cisco for small POE switch deployment.  Yay!So, I opened up my shiny new piece of hardware (a SF302-08MP aka SRW208MP-K9-NA), plugged in a Cisco 1230 and an 1121 AP AND... nothin...

Hi,I was wondering if someone can help me with my configuration issue. We bought one SG 300-20 switch and three SG-300-28 P. In our office we have Avaya IP Office (IP PBX), a couple of servers, and Avaya 1616 IP phones. We do not administrate Avaya I...

Hi,does anyone know if the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG swi...

Hi,How to monitor of CPU Memory Baclplane for SG300-28 (SRW2024-K9-EU)..?Thanks for your Input,,,,

I need some advice about the SG300-10 switch. My goal is to use it to connect 3 computers and a home made NAS (FreeNAS), using LACP. Each computer runs CentOS. My current setup is:Modem---- Netgear ProSafe SRXN3205-------- Computer1-------- Computer2...