Update: This portion of the project has finished earlier than initial projections. We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board fro...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Installation Guide - Catalyst 1300Hardware Installation Guide - Catalyst 12...
Cisco Switch 3650 SYST light flashing green and all the ports are not working, how do I fix this.
Hi,Until some weeks ago we had a setup of two SG500XG Switches with currently 4 Servers connected to them (2x RHEV Servers, 2x Storage Servers). Each Server hat 2 LAN Adapters so LAN 1 of each Servers go to Switch 1 and LAN 2 to Switch 2. We don't co...
We have a few cases where the configuration of the switches gets lost and they jump back to their factory default. Now about the procedure:We upload the attached configuration file.Afterwards we enter the webinterface and change the VLAN 1 into a sta...
I am having an issue with a VLAN carrying across two switches. I won't necessarily say it is the VLAN but maybe DHCP. I have a Trunk port on Switch 1 with VLAN tagging. It is VLAN1 Untagged, VLAN2 Tagged. It connects to a port on switch 2 that is a T...
Hello,I have a CBS350-16P-2G switch and am trying to use port 17 and port 18 with GLC-TE optics.According to datasheet this optic is supported:https://www.cisco.com/c/en/us/products/collateral/switches/business-350-series-managed-switches/datasheet-c...
We are using the attached configuration file.When now a certain device is connected to the switch, the message appears in the webinterface:afterwards the switch is not reachable anymore. if this device is disconnected and the switch rebooted it is ba...
Resolved! Lag and LACP 20g link possible?
Hi, So I have a stack of sg550x's, and sg350x's as the edge devices. I'm connecting them via lag groups with lacp enabled, and I was hoping to see a 20g link when connecting the 550x to a 350x (ports xg3&4) with 2 fiber connections Is that a thing wi...
In March 2022, it worked. I upgraded three SG350 switches (two non-PoE 24 port and one non-PoE 8 port) by backing up the running config from each SG350 and updating (importing) each into its CBS 350 counterpart (we bought the CBS models based on Cisc...
How hot do these CBS 250 run ? Today it is 100.4°F (38°C) outside and this is what the CBS 250 reports : T inside a cbs 250
HiI'm knew to CISCO hardware so please bear with me (also I'm using the GUI).I'm trying to set up 2 VLANsVLAN1: 192.168.0.0/24 - voiceVLAN2: 10.0.0.0/24 - dataVLAN1 will be connected to a BT router which will act as the DHCP serverVLAN2 will not have...
Hi All I have a SG350 switch that is the main switch in this network 2 Vlans setup (Voice and Data) All device are able to get dhcp as normal The IP Phone as well all get dhcp fine as well The issue is regarding a Snom M300 Base station...
Hi, I'm a little unclear on how essential Probes are with deploying the Cisco Business Dashboard.I have a lot of smaller sites (which is why I am using the SG/CBS series), so I am not keen on deploying a Probe VM at each one, which I then need to mon...
What is the memory utilization command for sg500 switch through CLI
hi,I am unable to find memory utlization for sg 500 switch?please help me for this
I'm trying to set up dot1x on our new Cisco switch. In general a basic setup with RAIUD authentication works fine so a big success on that front (tho I'm still in a generic testing phase).However I wanted to make use of the guest VLAN option to permi...
