@Reza Sharifi I need to know whether Catalyst 9200/9300 supports inter-VLAN routing with DNA Essentials OR the Advantage is required for this basic L3 functionality.
Forum Posts
Resolved! ip policy route-map
Hello folkds, I'm new to learning PBR, but I'm not exactly quite sure what is happening here: nexus- Core# interface Vlan2185 no ip redirects ip address 10.60.1.3/24 no ipv6 redirects ip router eigrp 1 ip passive-interface eigrp 1 ip policy route-m...
Cannot not putty into ISR4331 router via console port
Hi Friends, I am looking for EOL and EOS for Cisco Model WS-C3850-24T. whether EOL/EOS differ depends upon Software version? mine is below. #sh verCisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIV ERSALK9-M), Versio...
I have a c2951 router with a SM-ES3G-16-P service module installed. The SM-ES3G-16-P lost the IOS during an upgrade. I attempted to perform an xmodem with Tera Term, during the procedure I set the BAUD rate of the SM-ES3G-16-P to 57600 as is typical ...
Resolved! QinQ Termination on ASR920
Hi Guys I don't have allot of experience with ASR's first time deploying one of these. we have mainly been using ME3400 Switches as our Customer CE's. Our client is deploying a small office and we need to tunnell all client vlans across the provider ...
Dear members. I want to use this topology design on my network. So I decided to buy nexus 5010 and 2232pp. Before buying I want to ask you. Is it possible to use this devices for my design? Thank you
Hello experts. I have a requirement to route some traffic out of a separate Internet gateway - aka not the default gateway. Happy with access-lists and PBR generally, my quandary is this. On the 6500 I configure an access-list:ip access-list extended...
My Cisco router 2900 connected via interface vlan1 to ISP modem accesses the internet for just 5mins and after 5mins, the internet is no more accessible. I can access the internet non stop when I connect to the radio directly via a PC. But my LAN use...
Resolved! router on a stick cisco 2950
Hello,I am trying to do a lab for Router on the stick but it fails. Here is the scenario.I have 1841 router and 2950 24 port switch.1841 Fe 0/0 is connected to switch on Fe 0/1Switch hAS 2 Vlans namely vlan10 and vlan20when I no shutdown on vlan10 th...
Hi - I'm just labbing for ICND2 and wanted to connect a Router to Switch etherchannel through 2 ports on each device, but now having recurring error message: *Mar 1 02:05:11.452: %SW_MATM-4-MACFLAP_NOTIF: Host XXXX.XXXX.XXXX in vlan 1 is flapping be...
Hello,I am studying CEF and know the basic working of CEF. However, I need help in following questions:Question 1: I understand that CEF uses mainly Prefix, NextHop, and Interface information in its table to forward packet. It seems that Packets are ...
Hello, We have a setup where iBGP peers have IPv4/6/VPNv4 address-family peerings. In order to decommission it, I wanted to take the approach to de-activate individual af peerings. However found recommendations against doing that due to the potential...
Current I have the following network design (cisco 6500 – site 1)--------trunk------------(cisco 6500 – site 2) The 6500’s are configured to share certain vlans between both sites. On vlan 777 I also do OSPF for IGP between locations. Current 6500 t...
Resolved! Changing Native VLAN
Hi,I am just a basic learner and i am having a small issue in setting up my router and switch I am using a 2620XM router and 2960G series switch I have created 3 vlan 100,200,300 on a switch and have assigned those vlans to 3 different PC's and chang...
