I need to display hostname in logs. How do I make it?P.S. logging origin-id don't work, this command just doenst exit:(config)#logging ?buffered Set buffered logging parametersbuginf Enable buginf logging for debuggingcns-events Set CNS Event logging...
Forum Posts
Hi all, I understand bandwidth in QOS is use to guarantee a minimum bandwidthI understand police in QOS is to set a limit to the maximum bandwidth.class test_out police 1608000 50000 100000 conform-action set-dscp-transmit af31 exceed-action set-ds...
I have one question and I will try to keep it simple. I have a Catalyst 2960-CG Series switch. The model I have is WS-C2960CG-8TC-L. There are 8 Gigabit Ethernet interfaces with Ethernet only connections. There are 2 interfaces (9 and 10) that ...
I'm using a C2960X. I enter spanning-tree mode ?. The options are:mstpvstrapid-pvst I'd like to seek some clarification on the last two options. 1. What I understand is that using this pvst command will implement a Cisco version of STP/802.1d and...
Hi , I have Cisco 4506E (WS-X45-SUP7-E) 2units configured VSS Mode. on the Supervisor card it have 4SFP+ portsPort TenGigabitEthernet1/1/1-2 for VSS connection.Can I use TenGigabitEthernet1/1/3-4 for connecting to switch (data up-link)? Example : ---...
Hello Everyone, I'm facing an issue with Port-Security. I'm not sure if this is a normal operation or a exception condition or may be issue with TP-link router. Please could you help me to configure it? I configured Port-Security (limit is five) my a...
Resolved! Loadsharing with glbp
Hi,Attached is a diagram, would it be fine if glbp is run across the devices R1 & R2 at location B.R1 & R2 are 2 different service providers link which end up on the L3 switch.Would this work for outwards loadbalancing.All hosts are behind the switch...
Hi Guys, Greetings, I am trying to configure the switch in a way that Voice VLAN and Data VLAN can be assigned to different set of interface ranges. Below is the config that i have attempted but interface range 11-20 did not move to Voice VLAN 20. Is...
Hi Everyone, In spanning-tree pvst+ mode I noticed one of the port is showing alt port role . while going through the forums i found that RSTP port roles might have been amended int the 802.1d(PVST+). Just to see the behavior i shutdown the Gi0/1, w...
Resolved! Clear counter in Nexus 5K
hi all,just a quick one, i tried to issue a 'clear counter et1/x' on our nexus 5k switch but got an error saying it's part of a port-channel.tried to clear it using port-channel interface but can't. my question is, how do you issue a clear counter in...
Hi Expert. I would like to verify what is the default setting on Port Security for Cisco SG200 & 300 Series Cisco Switch. thanks.
After configuring aaa and tacacs configurations on a switch, it now asks for a username and password if even I did not configure a username and password. Please see aaa configurations below. aaa authentication login default group tacacs+ localaaa au...
Hi, Existing my company having a Cisco ISR3925 but i have no access on to the router due to the previous administrator do not left any login credential. I am thinking to get another loan unit and take out the compact flash from the existing 3925 and ...
I just got handed taking care of our switch's at work and have some questions, i have not worked with switch's that much but i know a little.i have a 2960 with 3 vlans 1 vlan for the ports 1 for the trunks and 1 for management with an ip. the switch ...
if switch is going to core as fiber from one uplink and copper from another uplink then this design will work or not?is it proper practice to do that
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 7 | |
| 5 | |
| 3 |
