I log in, go to IP Configuration --> IPv4 Interface, click the one and only VLAN1 to select it, then press EDIT... When I switch to Static IP Address, the IP Address field never becomes editable. Only Network Mask becomes available. I just updated th...
We have noticed recently that there is one switchport that will show TONS of MAC addresses, many more than could be possible. The client connected to that port is a 2017 MacBook Pro, connected to LAN through a BenQ monitor w/ a built-in NIC. Shut/no ...
Hi all, I recently received a SG200-26FP POE switch to upgrade my network to allow gigabit LAN. While attempting to setup the switch, I tested the switch by plugging in a few things, to see if there was any kind of network through the switch (yes). H...
Hi, I've just tried creating a VSS cluster with two C6832-X-LE switches and have experienced a problem after the initial reload once the command to convert to VSS has been issued on switch 2 : *Apr 30 10:52:10.931: %VSL_BRINGUP-3-MODULE_DOWN: Fai...
Hi I need to allow ip prefix matching from prefix-set allow-ilg1-pfx and ( as-path-originates123 or as-path-originates 321) will below statement work as I expected elseif destination in allow-ilg1-pfx and as-path originates-from '123' or as-...
I have a pair of Nexus 5548's that handle traffic between UCS blades and a SAN cluster. It is a datacenter FCOE switch that handles traffic for Vmware hypervisor hosting Windows VM's. I also have some catalyst switch stacks used for access layer traf...
need some help getting this going.. I have 2 SG500 switches in L3 mode, stacked, that will act as my main router. I then have several SG500 switches in L2 mode dotted around the business. I'm looking to cable 2 ports from each of the L3 switches ...
Hello all i am new here and hopefully can get some help with a packet tracer exercise im stuck with. I have attached the packet tracer exercise file as a link and the relevant word document. https://workupload.com/file/vxM4Kda So far i have done ...
I would like to enable ospf bfd for all ospf interfaces. What is the default OSPF BFD default values if I dont configure interval, min-rx, and multiplier? System image file is "bootflash:/asr1002x-universalk9.03.10.01.S.153-3.S1-ext.SPA.bin"
Hello, I noticed the periodic appearance of the following log messages: 01:57:21: %CPUMEM-5-FALLING_THRESHOLD: 1 CPUMEMd[6274]: Threshold: :2, Total CPU Utilzation(Total/Intr): :1/0 01:57:36: %CPUMEM-5-RISING_THRESHOLD: 1 CPUMEMd[6274]: Threshold: ...
Hi All, I am currently studying towards my CCNP Switch (300-115) exam, and need a little bit of help with VLAN Access-Lists. In the below configuration, i am a little confused what the point of the config starting 'vlan access-map NOT-TO-SERVER 2...
Hi fellow engineers,Hope you could help me out in this problem.This is just a simple static nat implementation but I couldn't make this work. :(Kindly take note that I just changed the first 3 octets of the public ip addresses.This is the static nat ...
I am looking to implement MSTP at our largest site and I was wondering if it may be better to split this into two seperate regions. We have 2 'sites' with 4500 series routers at each core, linked by a layer 2 dark fibre. Site 1 29 Switches (mixtu...
Hello All, I have 2 Distrubition layer one is work normal after the ospf but the other all the time i receive this massage the two dis ccconnect with the core by OSPF *mars 05, 03:22:27.2222: 03:22:27: %OSPF-5-ADJCHG: Process 1, Nbr 10.47.20...
Hi,I haven't work on any Nexus devices. But am keen to study them.Are there any simulators available for Nexus 2K, 3K, 5K and 7K...? Brgds,Ninad Thakare
