I'm trying to do a lab in PT. and get the following error: FIRST Router(config)#int G0/0 Router(config-if)#ip add 192.168.0.1/30 Router(config-if)#exit SECOND Router(config)#int G0/0 Router(config-if)#ip add 192.168.0.2/30 NOW, ON THE SECOND ROUT...
Hey everyone, Is anyone able to clarify what the benefit of using the following commands are, and what exactly are they doing?switch 1 role activeswitch 1 role standby1:1 redundancy is used to assign active and standby roles to specific switches in t...
Hi,I have 2 x C9500-24Y4C switches using 2 x SVl links. For Dual Active Detection I have 2 separate physical links and the option to use a C9300 switch with a PortChannel running ePAgP to the C9500 switches.Given the various options what is the Cisco...
HiWe have two Cisco CBS 350 "Stacked" connecting the ISPs routers with the SDWAN.My question is can I connecting two ports from one ISP router to these switches, as I need to connect one port to CBS-1 and second port to CBS-2. as the below diagramApp...
I started working on a new project and have inherited a 9200. I have been working via the serial port but would like to enable the web UI and can't figure out how. Does anyone know the CLI commands for a 9200 to configure the web UI?
Hi dears if i see advetise routes prefix to nieghbor X.X.X.X by details for example which community send wightand other bgp parameters How can see thisin bgp nexus switches for examples 9K series???
Dear all ,I want to support me I have wireless controller 2504 connect to device access point but I can not enter webpage so I want configuration this device but I can not enter webpage Best regards
Hello i want to solve this packet tracer lab :[![enter image description here][1]][1]I have this set of tasks to do :[![enter image description here][2]][2][1]: https://i.sstatic.net/YqhEbhx7.png[2]: https://i.sstatic.net/f3F9Nj6t.pngMy questions are...
So in our environment we have a cisco and netgear devices. Specifically 2960x and gs7xxtpv2(netgear). Our core 3750 is using rapid pvst (it shows up as rstp) and all of our netgear devices are set to rstp. We only have 2 vlans so it's a rather small ...
I feel like this should be a relatively straightforward question but I can never find a clear answer so maybe it depends on the environment. In our set up we have a combination of netgear gs724tpv2 and Cisco 2960x. It's a very simple environment we o...
Cisco Ethernet Switch - IE3300 (8U2X) with an Expansion Rack (IEM3300) with 16T / 16 portsPower Supply: PWR-IE480W-PCAC-L= (Power Supply is providing 54V and Switch is receiving the same supply)Under Power Management, Total Supported power is 125 Wat...
Hi All, We're using StackWise Virtual 9500 switch in a new deployment. Two firewall was running HA and two 9500 stacked together. All my VLANs gateway are in my firewall and 9500 was only layer2 mode. We’ve created VLAN interfaces in firewall and tru...
Hi!I want fo filter only one information when I run the command : sh log The log is :%PLATFORM_THERMAL-4-SECONDARY_OVERTEMP: Switch 1: Temperature is above normal (yellow) limit.Its possible to filter only the logs with the same information? Thanks!
Currently having issues with wireless devices not having DHCP when connected to the various Access Points. All steps are properly followed with video guides online, all DHCP works on Non-Wireless devices such as AP and Admin-PC, however, even though ...
I have two 3650 switches each connected to an encryption device.The GRE Tunnel required for the encryption devices came up right away, but the encryption is still not happening.The encryption devices cannot do an MTU over 1400, but I cannot set the 3...
