Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hi We're having "CISCO2921/K9" device which is configured with NAT overload with one external internal : ip nat inside source list 1 interface GigabitEthernet0/0 overload But this kind of configuration is not very useful to us because every day we...

Hi,  In 6513 if we have two SUP, one will be active another one will be standby. in 6500 switches backplane is lies on SUP engine not like Nexus. so if we have two SUPs one active other one is standby so only one SUP will provide backplane capacity? ...

hi,My objective here is to provide internet to all 8 ports, but i don't want them to comunicate between each other...The solutions i was trying to do here were:1 - assign a diferent vlan to each port. The problem with this is that i can only have one...

seclabs06 by Level 1
  • 298 Views
  • 1 replies
  • 0 Helpful votes

Hi i was wondering if anyone can help as we have received the new version of 48 port switch and our normal console cable is not recognised when using hyper terminal for configuration. It still works for the older models both 24 and 48 port set at the...

Lee Kemp by Level 1
  • 275 Views
  • 3 replies
  • 0 Helpful votes

We have two 3750's running VRRP acting as the first hop routers for three 2960 access layer 2 switches. Would it be possible to extend the VRRP service to two new ESXi 6 servers running VMWare, upon which is configured a virtual switch that supports ...

Docklands by Level 1
  • 1612 Views
  • 4 replies
  • 0 Helpful votes

Hi, I've been unsuccessfully trying to find a cause for this problem, we recently installed a Catalyst 3650 to act as a distribution/core (collapsed) switch and we're having issues with ports going down and up. I'm pasting here the show run, show log...

I have a L3 3750 that I am using for all vlan routing.  I have this connected to a sonicwall and that is the default route.  The primary vlan is able to connect to the internet without a problem, however none of the other vlan's are able to.  I have ...

sampson01 by Level 1
  • 1129 Views
  • 6 replies
  • 0 Helpful votes

HI,I am using a WS-3560-48PS with IPBASEK9-M version 12.2(55)SE6.Actually :I have 5 vlan configured with wired LANI have a new 100 Mega  internet acces with french provider connected to the switchModification :I need to install Access Point 1832 on o...

cbemobile by Level 1
  • 1568 Views
  • 15 replies
  • 0 Helpful votes

We're implementing a router at a local branch office that's directly connected to our primary data center via two pairs of fiber. I'd like to set up a port-channel from the router to each of our Nexus 7706 chassis using VPC. We do several layer 2 VPC...

aweise by Level 1
  • 312 Views
  • 2 replies
  • 0 Helpful votes

I am trying to document/justify all open port on my systems and I am finding all of my IOS Switches are running TCP 10002 show ip socket | include listen 17 ‐‐listen‐‐ 192.168.251.251 123 0 0 1001 0 17(v6) ‐‐listen‐‐ ‐‐any‐‐ 123 0 0 20001 0 17 ‐‐list...

blaroche by Level 1
  • 16041 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card