Switching

Hi team,    Here's something about NAT .    I want to do NAT to translate 192.168.21.21 to both 202.100.10.1 and 61.144.1.252 for the server can be accessed by two Internet addresses.    Configuration is as below:      interface fa 0/0        ip add ...

Hi, We just recently upgraded our Cisco switches to Cisco 3850 Switches. However, we have an old voice gateway that I'm having a hard time figuring out how to configure to an interface port on the 3850 switch. The configuration that I'm looking to a...

Hi, I have my ASA 5540 configured with IP address 10.0.0.1/29 in the INSIDE interface and a public IP in the OUTSIDE. Connected to the ASA I have a Cisco Switch 2960 (L2) with 2 vLan's: vlan 230 (no DHCP) with IP address 10.0.0.2 and vlan 4 (DHCP)...

Switch: WS-C3560-48PS-EIOS: (C3560-IPSERVICESK9-M), Version 12.2(53)SE2I have the above switch running at a small site; it is configured as the default gateway (10.x.x.1 - has multiple VLANs) and also currently gets its own time from an NTP server ac...

Hello, I am trying to setup Cisco Campus Fabric in a lab. I have created border/core/edge levels with 3850 switches. My underlay uses EIGRP routing and each switch has a Lo0 that is reachable in the underlay. I have connected the underlay to my "ext...

Hello, I have a Gigabit port which is only negotiating half duplex. This is a service provider secondary WAN uplink spec'ed at 30 Mbps. They state that their side is set to full duplex but not sure what their speed settings are. I hard-coded to full ...

Dear Members, I am a newbie to Cisco products,  It is my first time with Cisco products ever. I need your help configuring my C881 K9 router recently purchased in order to connect  (ability to ping) my PC  (192.168.1.x) with different LANS  ( belong...

I have run into an issue. This is my first time using Nexus OS. I know that on my previous catalyst switches i could use show vlan to get a list of what ports were connected to which vlan.  43 VLAN0043 active Gi2/3, Gi2/11, Gi3/3, Gi3/11 Now on the...

www.cisco.com/c/en/us/products/collateral/routers/4000-series-integrated-services-routers-isr/datasheet-c78-732542.html The ISR 4351 has 3 x onboard LAN/WAN ports. I presume these ports can be turned into standard switchports (i.e. if I want them in ...

Hi, I am using Cisco 3825 router and 3750 switch in my network. My query about to use  public ip in  my lan client PC . I have two isp directly connected to my router both Ip address  block is /30 i have /27 public ips pool from one ISP and i want t...

I currently have a WS-C3560-24PS with SW Version 12.1(19)EA1d. The lowest version I can find on Cisco is 12.2(25)SE but the minimum IOS version needed for the upgrade is 12.2(18)SE. I am unable to find 12.2(18)SE. Any help would be greatly appreciate...

Hello, I have the need to send the logs from Cisco Switch to Syslog Server. I would like use kibana. Somebody used kibana with Cisco IOS before? Best regards,

I have an ASA that is solely being used to attach to AZURE's VPN If i attach to the inside network and use 10.0.0.13 as the gateway i can get onto the vpn network.  I'm trying to add this to our core network but the OSPF routes are not being showing ...