Hello Everyone,I'm planning to deploy C9300-24S stack of two with modular uplink(C9300-NM-8X1). I need to know:Q1. As i can see the switch is not going to consume much power because of SFP port, Can i use two redundant power source (PWR-C1-350WAC) fo...
Forum Posts
what are those messages ? it this a bug ? Platform: 3750x IOS 15.2(2)E3 002864: 000430: Jul 15 03:54:05.035: %PLATFORM_MCAST-3-IPV4_ERR: Cannot load multicast routing entry in hardware as corresponding TCAM region is full. (Condition hit 1 times si...
Good Afternoon, I know nothing about Cisco Switches or VLANs. We currently have a PfSense Firewall with VPN and conducting all of our VLAN routing to a Cisco Layer 2 Switch. Drawing and config files for PfSense and Layer 2 attached. I was tasked with...
I am working with Router on a Stick. I have set this up a few times in Packet Tracer. I can never get the router and switch to ping. Everything else works great. I have setup ip for vlan 1, set default gateway for vlan 1 and in global, made sure vlan...
can anyone help to change the below Juniper 802.1x config to Cisco 9200 config. set protocols dot1x authenticator authentication-profile-name CLIENT-AUTHset protocols dot1x authenticator interface OFFICE-LAN supplicant single-secureset protocols dot1...
Good morning , please could you support to us in the following question? 2960 24 TC-L one of its feature is 2 dual purpose uplink ports , it means one RJ-45 and one SFP port , by default when we start the switch the SFP port goes to active keeping...
Hello. I have a question:I have 2 trunk ports in port-channel with LACP. One of them is down. But what happens when this interface goes up. My understanding is that when LACP negotiation is finished the traffic start passing over the link, but some V...
Hello community!I have two 93180YC-EX in VPC, NX-OS mode: BIOS: version 07.66 NXOS: version 7.0(3)I7(9) Sometimes we experience unknown unicast flood for ~1-3min due to disappeared MAC. This situation arises every several hours randomly. At the time...
Hello,I have recently gotten a 4948-10GE and am trying to get it setup to be used for my home networking lab. I am unable to get any type of connection to the switch with a direct connection from my PC plugged into the MGT port. I have the PC NIC se...
Hello all,I am starting small and purchased the Cisco 110 series unmanaged switch. I just connected my XFinity cable modem using the provided yellow ethernet cable to the cisco 110 on ethernet port 1. I have noticed at the upper left LED light is fla...
I need to connect the Meraki switches below on single-mode fiber. We tried all the combinations, including swapping cables and changing SFPs, unfortunately, it won't work. Could anyone help me which SFP is compatible? switch model: MS225-24 ---->> MS...
Is the CVE RECORDS FOR RTMT has been work around as I can see update of the cve records but not it's solution . Is the CVE Records for RTMT remains same for version 14 and above
Does anyone have the appropriate way i could enable logging in the syslog messages to see what commands are sent to a box from a user? Trying to debug a script and i'm aiming to see what the box itself sees as far as commands and logout requests. Cur...
Hello Team, I need your assistance, I've trying to configure radius authentication with Cisco switch to be authenticated from the NPS server, as shown below I've created 2 network policies on the NPS radius server first policy for TLs with shel...
Hello all. We have several switches reporting the following error from Solarwinds" Power Supply B on XXXXXXX is Critical" Where there is NO B installed? The SW version is 17.3.6
