Hi All,I've taken on the role of looking after our C9500 and I'm trying to figure out what level of hardware support (if any) we have through our existing Cisco switch licensing.We have: C9500 Network Advantage and C9500 24Y4C DNA Advantage.Does havi...
Forum Posts
Resolved! Stackwise Virtual on C9407 with SUP-2?
I have a pair of C9407, each is installed with a pair of SUP-2 (active/standby). I want to setup the two 9407 as a stackwise virtual domain. Referencing to the High-Availability guide, linked below, quote "Cisco StackWise Virtual can be configured o...
Resolved! IOS XE for ISO 270001
Hello everyone,I have a Cisco C9300L-48P-4X with IOS XE 17.6.5 software. I will conduct an audit in a few days, is the IOS version in accordance with the ISO 27001 standard? If not, what version of IOS is compliant with the standard, with a stable ve...
HiNewbi here so please be nice.I'm using a Cisco 3132 switch. I have 2 40 gb connections but only getting 1 gb transfer ratesAccording to linux networking app it shows 40000 mb/s connection.According to Cisco 3132 it also shows the 2 ports at 40 gb...
Hello Team, im working on a task to enable the aaa new-mode on our cisco switchs my question is what is the difference between the below commands?#aaa authentication login default group rad-groups local #aaa authentication login default local group r...
Hello Cisco Community,i want to remove the sync-profile on each of two synchronized Nexus 5596UP without loosing the config stored in Switch-Profile. That means without connectivity interruption and re-configuration of interfaces in "conf t mode", fo...
Hello Experts,I am stuck in one issue , i am trying to apply PBR on SVI configured in VRF.Its throwing me error "Can not apply route-map to this interface if VRF is configured".Basically our next hop is in Same VRF , i want to match some host in ACL ...
Hi,I'm interested in throttling/restricting the bandwidth on a particular interface on an IE-4000-8T-4G-E running IOS 15.2(4)EA9.Previously when using Cisco 2960 based hardware we've used, "srr-queue bandwidth limit" as the method for speed restricti...
Hello! So I'm working on a project on gns3 that uses VRRP v3 with IPv6, what I'm trying to do is to configure a pc's default gateway as the virtual ipv6 of vrrp, (i'm using a router as a pc and already entered: no ip routing command), but when it com...
Listen here: S11|E4 Power Meets Simplicity with the Catalyst 9300-M With the growing number of distributed sites and increasing bandwidth requirements, networking teams must rethink their network operations and network security strategy. Cisco Cataly...
Resolved! Nexus 9k High cpu oid
Hi There, I just wanted to monitor high cpu logs of nexus 9k with snmp server . Can you help me to get correct OID to get high cpu logs. Thanks in adv.
Hello,I have a 9800-80 (HA Pair) running 17.9.4a code. We've observed intermittent delays with vocera broadcasts. Media-Stream multicast direct is disabled on all the WLANs. "show ap multicast mom" command shows the AP as "up" for the multicast com...
I would like input from the community. Would load balancing DHCP requests across multiple servers using Cisco switches provide true-load balancing where the load is evenly distributed based on server capacity or current load using 2 IP helper-address...
Resolved! Clear the config off an interface
Is there a way to clear the configuration off a single interface in one shot, and set it back to defaults? I have a 6509 running an IOS.Thanks,Mike
Resolved! C9200L Config Not Saving on Reboot
Hi,I'm trying to set up a C9200L-24T-4X-E-RF switch. I'm setting it up using the following commands but it seems the configuration is not being saved between reboot.switch: boot flash:/cat9k_lite_iosxe.17.03.05.SPA.binSwitch>enableSwitch#config tSwit...
