....(Example: se 2/0 to se 3/0 when configuring EIGRP?) Please examine attachment. Thanks, joe.
....(Example: se 2/0 to se 3/0 when configuring EIGRP?) Please examine attachment. Thanks, joe.
Good evening,I have purchased a new 2960 - S switch catalyst and have configured one SVI (interface -Layer 3). But my problem is that can't to use the show ip route command on this model. This device has the universalk9 flash. Thanks in advance!
Hi,On a 3750X that is routing vlans, is there a mechanism to treat one particular vlan differently so it cannot be routed?This switch is connected an ASA inside interface and to the same ASA dmz interface (not our recommended way of doing things) but...
I have a router on a stick running two vlans. How would I configure vlan routing so that both vlans can access the same host on one of the vlans?
Hello,My workstation can resolve domain name, but my router cannot I receive the following:Router#ping www.google.comTranslating "www.google.com"...domain server (8.8.8.8) (8.8.4.4) (75.75.76.76) (75.75.75.75)% Unrecognized host or address, or protoc...
I have got 2 switches facing to each other through an L3 etherchannel:SW4(config-if)#do sh ip eigrp neiEIGRP-IPv4 Neighbors for AS(10)H Address Interface Hold Uptime SRTT RTO Q Seq ...
I recently moved the subnet 10.0.50.0/24 into a VRF. After doing so I realized this broke one of my NAT translations:ip nat inside source static tcp 10.0.50.230 22 interface GigabitEthernet1/1 9022I located the following document: http://www.cisco.c...
Good Day.I will be performing 4500 non-E chassis to 4500E chassis upgrade this week.non-E chassis has IOS 12.2 running on it while 4500E will have IOS-XE 3.2.5SG code running. Is there any website where I can paste the IOS configuration to see if the...
Hi everybody Basic question, I would like to know how much traffic the is switch forwarding in Layer 2.In other words, a simple set of counters that in an aggregated way includes statistics from all interfaces.Any show commands or SNMP MIBs are welco...
I have a cisco 871 router and I am not able to make a pppoe connection with ISP.Config:Building configuration...Current configuration : 2043 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno ...
Hello, I'm using a Cisco Router 1941, and working on configuring a Proxy Server. I have a system which I have installed Ubuntus 12.04 and configured Squid to work as a proxy server. The configured proxy is working on the Ubuntu server as required. Ho...
Hi, L3 switch (routing) ----- ISP (private MPLS) ----- L2 switch (2960 - Main Comms Room) ---L3 Switch (3750) (satelite cab) I have a question regarding the above design and to implement this. We have a l3 switch and another office to connect. But ...
Hi, I have setup a vlan interface for our guest wifi. Our internal network uses the outside interface IP for it's NAT. I would like the guest network to use a different IP address.If I specify the IP address to use, it does not work. If I change it t...
Hi, The following is the partial config for etherchannel on our 4500 switch.interface Port-channel3 description XXNAMExx switchport switchport access vlan 40 switchport trunk allowed vlan 40 switchport mode trunk! As the switchport mode is trunk I ...
Hi Cisco Guru,I have a problem with my Cisco Router, here I Attach the show run my router :version 15.3service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname Router!boot-start-markerboot-end-mar...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-20-2024 09:12 AM | ||
08-06-2024 12:40 PM | ||
08-05-2024 10:24 PM | ||
08-01-2024 10:26 AM | ||
07-24-2024 06:05 AM |
User | Count |
---|---|
5 | |
4 | |
4 | |
4 | |
4 |