Buy or Renew
Buy or Renew
NOTICE: You can now engage in the community. Learn about the great new Cisco Umbrella content.

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! newbie snmp question

Hi,We have a Catalyst 3560 Series switch in our data center, and we want our provider to send us a bandwidth graph of this switch and I have to enable the SNMP for this switch.I have 2 question,1. to enable and allow the provider access to our switch...

3750 - Switch removal - port down

Hi all.Today i decomissioned a switch from my 3750 stack. Upon recabling my stack i have lost a member from the pool. The switch is operational and performing as normal but is missing from the stack. Upon closer inspection it appears a port is down. ...

Cisco 4500 Sup-6 QoS configuration

Was surprized to find out that 12.2(46)SG has MQC QoS, so no mor LAN QoS.Very good, long time awaiting ...QoS configuration page for 45oo Sup-6 is very simplistic and does not really open up the differences between long existing MQC on routers and MQ...

Catalyst 4500E Supervisor VI QoS changes

I have upgraded a Cisco 4506 with a Supervisor 4 to a Supervisor 6-E and low & behold, my CoS/QoS settings no longer work.  I see from a white paper that Cisco upgraded the supervisor capabilities to MQC, which is more inline with the IOS routers.  T...

valnar by • Level 1
  • 4150 Views
  • 5 replies
  • 0 Helpful votes

Resolved! QOS IPP DSCP question

Hi folks,I am new to QOS and will be gratefull if someone here could help me out. I have the following setup Client ----- port F0/1(SwitchC2960)port G0/1 ------ trunk ------ port G3/4(Switch6500) port G3/7 ----trunk---- port G0/1(SwitchC2960)port f0/...

Resolved! N7K/fabricpath/vPC peer link

HelloI'm having trouble understanding what the issue is.I have 2 different networks, each with 2 pairs of N7K's (each using 2 VDC's) with multiple N5K's connected to all N7K's and both the VDC's.My set-up works fine for one network but not for the ot...

Host to other Switches?

               Hello, I'm trying to ping the Call Center Switch and the Engineering sw from IT and it should be successful       (phase 5 testing) I applied the acl correctly and checked the ip route & it's ok, however it still does not work. Here's ...

vranxid01 by • Level 1
  • 252 Views
  • 1 replies
  • 0 Helpful votes

LACP Configuration with two links

Hi,Does LACP provides load balcing & Redundancy together  on an ether-channel with two links?I have two links to my access switches from distribution swith. Which etherchannel protocol (LACP/PAGP)will give me redundacy as well as load-balancing/bandw...

sadash008 by • Level 1
  • 706 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Inter-VLAN Communication

I have set a VLAN network.I am able to ping members of same VLAN domain but inter-vlan pinging is not getting any suiccess.I am using router for this purpose.Here is the packet-tracer file.Please help me out. http://www.mediafire.com/download/50s1emf...

WS-X6724-SFP can't boot online

     I'm going to upgrade IOS version on a 7606-S router to 12.2(33)SRD5.  First, I execute 'redundancy reload peer' command, boot standby RSP720 with new version IOS. Then , I execute 'redundancy force-switchover' . After the RSP switchover,  both W...

mengyan by • Level 1
  • 846 Views
  • 3 replies
  • 0 Helpful votes

6509-E Fan high power

I am trying to install a new 16 port 10 Gig interface card in a 6509-E chassis, which is supposed to be fully supported.  But when the card was inserted, it said that not enough cooling was available for the card (it says 70cfm per slot are available...

Resolved! Wildcard Mask

Hi!I want to know about wildcard mask, 1) what is that and why do we use it?2) wildcard mask that we use in OSPF and in ACL, what is difference between both of them?I mean in OSPF we say network 1.1.1.1  0.1.0.1 and in ACL we say access-control 5 1.1...

MAC Entries in 'Mac Address Table' of Switch

Hi All,I am new to CCNA and doing with switching part currently.I am facing issue in understanding how is the entries in the MAC address table of the switches are made.What I know is: MAC addresses in MAC Address Table of switches is the MAC of hosts...

azmunnabi by • Level 1
  • 3257 Views
  • 7 replies
  • 0 Helpful votes
View All
Review Cisco Networking for a $25 gift card