Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

partner support: what is included in the flavour

                   HiDoes someone know where I can find a document that explains the several Cisco Partner Support Services, SmartNet, ....I would like to know a clear description what is included in the several flavours:For instance CON-PSUP-, CON-P...

janvandek by • Level 1
  • 9892 Views
  • 1 replies
  • 0 Helpful votes

Resolved! 2960 Output Drops

I have a Cisco 2960 switch connected to a 4948E via port channel and I'm seeing output drops on the 2960 on the port channel.  On the 4948 where it is connected I don't see any input or output errors.  Could it be just because of the smaller buffer s...

ALIAOF_ by • Level 6
  • 11286 Views
  • 12 replies
  • 0 Helpful votes

Resolved! IP fragmentation

                           G1/2                         G1/1PC1 ---------- R1 ------------------------------------------- R2 --------------- PC2                           MTU = 600 bytesAll interfaces have default interface MTU with length 1500 bytes...

speed negociation delay

I've got an infrastructure with gigabit 4500 switch and connected machines.Machines connected with standard twisted cable (4 pairs) works fine and negociate quite instantly to G : no problem.When have to split one plug and connect 2 machines (2 paris...

Resolved! traffic-export capturing only inbound traffic

HiWe have a Cisco 2811 running ITP IOS.  On that router we run the SMPP service.  A client on the network connects to this service, and we need to capture the traffic for debug.I've tried traffic-export, but I cannot see any outbound traffic.I'm gues...

Resolved! ip dense mode, how and where to enable state refresh.

Hi everybody.Let say we have a  network as shown below:10.10.10.1      s1 ( pruned)server----------R1----------------------------R2                          |                                         | s0 ( pruned)                          |          ...

sarahr202 by • Level 5
  • 436 Views
  • 2 replies
  • 0 Helpful votes

Cisco ASA: routing issue

I am stuck on an issue that is most likely going to turn out to be a simple resolution and be the result of my not truly understanding what the heck I am doing (at least I can be honest).I have a ASA 5510. The management interface is connected to an ...

Resolved! Catalyst 6500 boot process

Hi,Can anybody explain me or point me to document which explians normal booting sequence in a 6500 Switch running IOS.What I am looking for is in which order the image is loaded in SUP, RP, SP etcThanks,

Resolved! RIP into EIGRP Redistribution

Hello,In this scenario, i am trying to redistribute RIP into EIGRP on a core switch. The core switch runs both RIP and EIGRP protocols and RIP routes are received from an external router which is filtered off using distribute-list inbound. After redi...

Resolved! Regarding STP loop

Hi Team,Whenever there is a looping in switch how other switch and the same switch where loop occured will get a information about looping. What BPDU carries to inform about looping in a network.PLease clarifyThanks in advanceNaveen

Resolved! sh ip int bri

What is the difference between 'nvram' and 'manual' in below output .Interface                  IP-Address          Method      Status                ProtocolGigabitEthernet0/1    X.X.X.X                NVRAM        up                    upSerial0/0/...

Resolved! QoS on the 4510 SW.

Hi all, I am new to QoS but I fully understand the concept. I inherited 3750(Stacked) and have the following QoS statements that I need to implement on the 4510: mls qos map cos-dscp 0 8 16 24 32 46 48 56mls qos srr-queue input bandwidth 90 10mls qos...

Load more
Unanswered Topics
View All