Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Dear all,When i connect my switch to hyperterminal using console cable, switch boots perfectly but i cant see the prompt. Instead of that i am getting below:%LINEPROTO - 5-UPDOWN : Line protocol on Interface Vlan1. Changed state to down%SPANTREE- 5 -...

Resolved! Show Policy-Map

Hi,I have applied QoS on the ATM interface hoping to improve the VoIP calls quality.interface ATM0.1service-policy input QoS-PM-Voice!ip access-list extended QoS-ACL-Voicepermit ip 0.0.0.0 0.0.0.0 123.123.123.0 255.255.255.0! class-map match-all QoS-...

leepeiwai by Level 1
  • 3979 Views
  • 6 replies
  • 0 Helpful votes

Hi,We are planning to do IOS upgradation in our Switches . Please suggest recommended IOS versions.Currnet IOS------------------------------------------------------c3560-ipservices-mz.122-35.SE5.binc2960-lanbase-mz.122-35.SE5.binc3560-ipbase-mz.122-3...

r5a5m5 by Level 1
  • 1077 Views
  • 7 replies
  • 0 Helpful votes

First of all I want to say I don't think the 2960S Lan-Lite switches we have can help, but I figured I would tap in to the brain power of all here to make sure there isn't a solution I have over looked. We have a few hundred branch offices that are a...

                   Hi,Some of our users intermittently got disconnected from the network and then reconnected back automatically after a few seconds. We are using Cisco IP phones and the desktop PC is connected to the Cisco IP phone. The issue seems ...

I have an issue that I don't know if this is an issue with Nexus or the sniffer box itself.Nexus software version:Software  BIOS:      version 3.5.0  loader:    version N/A  kickstart: version 5.0(3)N2(1)  system:    version 5.0(3)N2(1)  power-seq: M...

Hello,I need your help to understand Vlan ID’s and trunking.We have three or four networks in place with some twenty subnets /Vlans from Vlan1 10.1.1.x, Vlan2 192.168.0.x, and so on to Vlan 129. We have two new businesses with the same subnets like V...

pain112 by Level 1
  • 3504 Views
  • 4 replies
  • 0 Helpful votes

Hey everyone!!As I was preparing for my ICND2 test yesterday, I thought maybe to get more hands-on experience with the equipment I would take my lab equipment and insert it into my home network.  My setup goes as of right now:3550 -> 2621 -> cable mo...

Hello Experts,Below are the commands I have to run on our PROD L3 Switches and need to know if it could make an impact on services.router bgp 65099 no neighbor 192.168.12.1 route-map prepend-AS in  (Is there any possibility that after executing this ...

ray_stone by Level 1
  • 1467 Views
  • 10 replies
  • 0 Helpful votes

Hello,I am new to bgp and have trouble configuring it in my project. My network has four different regions (1 through 4) and it connects to four different ISPs (AS 100, 200, 300 and 400). Regions 1, 2 and 4 have five routers each while Region 3 has s...

Greetings .... I manage a small/medium sized campus network consisting of 4 Cisco 6500 series chassis (each with SUP720's) and a couple hundred Cisco 3550/3560/2960 edge switches. We recently completed a new leg of fiber that will make a completed lo...

swilk by Level 1
  • 1361 Views
  • 4 replies
  • 0 Helpful votes

Does anyone know the best way to configure NIC teaming switchports for HP servers?Currently we have a problem where servers are connected to the switches in a dual NIC fashion and are teamed. The server transmits out of both interfaces but receives o...

adil.javid by Level 1
  • 12356 Views
  • 19 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card