Does C9600-LC-48TX support speed 1G on C9600X-SUP-2 ?
Forum Posts
I am considering adding 93240YC-FX2 to my network, and I found on the installation guide that this switch can work on 12 x 40/100G ports, 16x25G , and 16x10G ports in the port side intake mode. My question is, if I will use 12x40G ,and 10x25G , how m...
Hi I have been told that you can now get CPU & memory Values for Switches and Access Point in the Meraki Console. I am very new to Meraki and cannot find this. Does anyone know and can point me in the right direction
The fiber starts up and then goes down and the below error appears.LINK-I-CHNGCOMBOMEDIA: Media changed from copper media to fiber media on port gi9 CONFIGURATION IS BELOW v2.5.9.54 / RCBS3.1_930_871_120CLI v1.0file SSD indicator encrypted@ssd-contro...
The fiber starts up and then goes down and the below error appears.%LINK-I-CHNGCOMBOMEDIA: Media changed from fiber media to copper media on port gi9CONFIGURATION IS BELOWv2.5.9.54 / RCBS3.1_930_871_120CLI v1.0file SSD indicator encrypted@ssd-contro...
Hello All,I am trying to figure out a couple of answers and could not find the answers by myself.In Packet Tracer (Physical Mode):How can I unplug a cable if I put it in the wrong port (RS-232 cable accidentally into Ethernet port)? How can I unplug ...
Resolved! Overlaps with vlan
Hello, I'm new to networking trying to configure Layer 3 Switch. I have calculated subnets for each vlan```Vlan 10 - 2 users200.100.10.0/29200.100.10.1200.100.10.2-3200.100.10.4vlan 20 - 10 users200.100.10.5/28200.100.10.6200.100.10.7-16200.100.10.17...
We are using the C1300-16FP-2g with a PoE+ device. We have control to a degree of how much power each device can draw. When we push each port over 13W, closer to 13.5-14W the switch will begin to shed ports (turn them off). At 204W we are about 85...
Resolved! STP UplinkFast and BackboneFast
Hello, everyone. When it comes to UplinkFast, my study resource says that if a device loses a root port, it can immediately have a blocking port be chosen as the next root port and transition into forwarding without going through the listening/learni...
for ios-xe, is it possible to be like IOS that we can do all the preparation works (pre-upload the image + setup the boot variable) and only at deseriable time then we proceed with the reboot?reason for asking is i will like to reduce the downtime ne...
I am seeking your assistance in setting up and verifying a load balancing configuration between two ISPs on my router. Below are the details of my device and the current configuration for your review:hostname Routerno aaa new-modelip dhcp excluded-ad...
On the downloadpage for 2960X (https://software.cisco.com/download/home/284795742/type/280805680/release/15.2.7E11?i=!pp) switches I can download 15.2(7)E11 but the release notes for that version are missing:https://www.cisco.com/c/en/us/td/docs/swit...
Hello,We are deploying an appliance that required mirrored ports on our Meraki MS250-48FP. I created a source and destination mirror. The company that provided the appliance is saying that they are only seeing unidirectional flows.How can
I have 9300 switch with below module. Module support 8 Combo ports I see 8 Ten Gig Ports but only 4 1 Gig ports. Also i cant use Gi interface I configured Gig 1/1/1 interface as uplink but it brought up Ten1/1/1 interface instead. How i can use C9300...
Dear all, I think normaly L2 MAC address table contains in Cat65 SUP' PFC as CAM table right? Basically all the memory support ECC feature except MSFC? here is the related link. Catalyst 6000/6500 System Crashes Troubleshooting https://www.cisco.com/...
