Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Looking for help!PC------Vlan10--\                 \--Switch--Trunk--Router--S0/0---WAN--(R-S)--Netflow_collectorServer--Vlan20--/We have user PCs and Servers that need to be in the same broadcast domain.We also need Netflow to forward PC-Server comm...

fsebera by Level 4
  • 1171 Views
  • 1 replies
  • 0 Helpful votes

Hello,I have the following ACL:ip access-list extended TESTpermit tcp 192.168.1.0 0.0.0.255 any eq wwwWould it permit only HTTP or any service via 80 port (like skype, youtube streaming, etc.)?Thanks.

Hello,We are having some problems with the CPU levels of a 2960 switch. We have configure SNMP notification with the following command:process cpu threshold type total rising 70 interval 5As we understand, that command is configuring the switch to se...

I have layer3 switch with 3 vlans on it.  One of the 3 vlans, I don't want to it be used for intervlan routing.  So I need it not to show up as conneted in the routing.  This one vlan is really just Layer 2 traffic, but since I am running DHCP for th...

Hi all,I'm working on a little OSPF setup in my lab and having a problem pinging out to the internet...I have a setup with (3) 3550's running ip routing. I'm configuring OSPF but I can't ping the internet from any L3 switch except the switch with the...

mtehonica by Level 5
  • 1867 Views
  • 3 replies
  • 0 Helpful votes

Hello,I got the following issue.The router is getting multicast feed. It gets it via IP PIM SSM config and the feed is sourced from the outside of the enterprise. Is it possible to convert this multicast feed into something that can use the internal ...

k.lapczuk by Level 1
  • 870 Views
  • 2 replies
  • 0 Helpful votes

Resolved! OSPF vs. RIP-2

The main difference between the two is convergence time. RIP-2 considers link as failed after 180 seconds not receiving updates from it, compared to 40 seconds for OSPF. And OSPF sends route updates immediately in contrast to RIP which sends updates ...

I need to install a 48-port 10/100/1000 line card into a 6506E. Can this be done whilst the switch is up?The hardware installation guide doesn't indicate either way.

g.leonard by Level 1
  • 1336 Views
  • 4 replies
  • 0 Helpful votes

Hi,As far as I know when using VTP v2 you just have to enable pruning in anyone of the domain's VTP servers in order to activate it too in the other VTP servers and clients. I'm deploying VTP v3 in my network but enabling pruning in one of the VTP se...

Hello,Usually I configure QoS with a single Policy-Map that contains more classes (voice, video, data, default), that is applied to all Access Port on an Access Switch or Access Stack.I'm wondering if instead of using the definition above (single Pol...

oguarisco by Level 3
  • 730 Views
  • 2 replies
  • 0 Helpful votes

hi ,i have the topology below-network---------------------------------------router----------------------interneton router i have bgp protocol ,its only default router which is leardned from my isp .in my router i confifure a default static route to m...

Dr.X by Level 2
  • 1443 Views
  • 3 replies
  • 0 Helpful votes

Resolved! stp timers

Hi everybody.Please consider the followingSW1---------------R SW2-D---------------BSw3sw1 is root port and transmitting its timers as:hello 4 secforward delay 35 secmax-age 50 sec.Sw2 receives the bpdu containing these timers and relays it sw3.Sw3 ha...

sarahr202 by Level 5
  • 8908 Views
  • 3 replies
  • 0 Helpful votes