Hi ALL, as far as I know that native valn is used for configuring Trunk ports . IF right then tell . and what is then DATA VLAN. Is any VLAN created for Access PORT is DATA VLAN . Right or Wrong ! Please HELP Thanks in Advance
Hi Guys ,I have Big problem since last week !I installed HWIC 1ADSL on my router but when i try configure it i can't show interface on router !Please anybody can help me urgent.Thanks so much
I have the following configtrack 10 ip sla 1 reachability delay down 5 up 5ip route 0.0.0.0 0.0.0.0 10.71.0.1 name DEFAULT-ROUTE track 10ip route 0.0.0.0 0.0.0.0 1.1.1.2 20ip route 4.2.2.2 255.255.255.255 10.71.0.1 permanentip sla 1 icmp-echo 4.2.2.2...
Dear AllI was reading some documents recently and got confused by below statement regarding the FD Calculation"The lowest-cost route is calculated by adding the cost between the next-hop router and thedestination—referred to as the advertised distanc...
Hi, I got a WLC and I log to the Web Interface, when trying to setup the AP I see there is a kind of status that reads: Operational Status: Downloading, what's supposed to be downloaded.Thanks
Hi all,I know probably a very simple one however getting a little confused.I have a single switch stack comprising of 2 x c3750 connected via stackwise.Customer is connecting to it with 1 fiber connection currently and I have another ready to be plug...
I have set up stack power on my 3750 stacks, they show as redundant but the stack topology is still showing as standalone. I am confused on how to get the Stack Topology to Ring as opposed to Standalone.
I want to copy and restore ios on Catalyst 2960G-48TC-L. It has 12.2 with Web-based Dev Mgr, and I want to upgrade to the current 15.0.Before doing so though, I want to backup the 12.2, so I typed the following:show flash2 drwx 192 Mar 1 1...
Hi,Let's say I have a stack of two 3750s, 24 ports each (48 ports total). The backplane is stacked correctly.I also have 20 Servers and switches which need to be availble to network users 24x7x365.How do I plug these 20 servers and switches into the...
I have an ASA with 2 networks locally communicating with a remote PIX through a VPN connection. The ASA network 172.16.10.x is communicating through the tunnel to the PIX network 172.16.11.0 just fine as desired. The 2nd network on the ASA is 10.168...
Dear All,I would like to as you that i have swich 2960 (10Unit) and switch 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check perfor...
Hello Guys,I was adding a new SUP on slot 1 of a 6509 in Hybrid Mode.This switch had been running only on SUP 2 for around 6 months.I added the new SUP, everything Ok. I failed-over the new SUP, everything Ok. I failed-over SUP 2 and the hosts attach...
Can anyone please help me out in understanding VLSM. i am having a hard time understanding it. spent alot of time on it and still got nothing out of it. I have the lammle book and i didnt get it right into my head. i want plain and simple method plea...
On September 10, I got this automated email regarding a bug that has been fixed and yet that version has not appeared in the download section yet.anyone knows how long it normally takes for the code to become downloadable. It seems like a long time t...
Hi,I have a Nexus 7K running 5.1.(1a) with N2248T as Fabric Extender.I had two ports on N7K-M132XP-12 module connected to N2248T.In order to activated fex feature I issued the following commands :install feature-set fexfeature-set fexWhen I tried to ...
