I have both types of stack kits but they have the same part numbers?C9200-STACK V01800-104767-01 Also is there any difference between C9200-STACK V01 and C9200-STACK V02? Thank you in advance for your feedback.
Forum Posts
Does the PWR-IE170W-PC-DC power supply output its full power via one connector or does it require both output connectors to get the full capacity out of it? I am needing to have 2 to power a IE4010 switch to get the maximum POE capacity.
Resolved! c9300 system loop
I have a c9300T switch that I am trying to configure for the first time, and for some reason, the switch itself keeps going through this weird system loop that I have never seen before and does not allow me to make any input into the CLI. I was think...
Hi, The command "logging origin-id hostname" on NXOS seems to not work with version 7.0(3)I1(2), how to solve the problem? Syslog server did not see the originator switch N9K coming in. I found this from https://community.cisco.com/t5/switching/is-...
Good Morning, Everyone. I am consoled into this switch as a priv 15 user and I am not even getting the chance to define where the TFTP server is. Please see my output below. I can't find any search results on this problem.Switch#copy tftp flashDestin...
I have a Nexus 3172T NX-OS v9.3(8) with two ports bundled in an LACP EtherChannel. The other end of this is a Windows 2019 server with Windows LACP NIC teaming setup. This has been working fine for quite some time then suddenly I'm finding this ser...
Hi Experts,I have trunk port connected to cat9500 where I would like to NAT.VLAN 5 is allowed on the trunk port and this vlan is used to run EIGRP to share routes between the Cat9500 and the upstream device.Is it possible to apply NAT on the SVI of V...
'C2960X-STACK= ' module is EoS ???????
Resolved! SG300-10 Firmware upgrade beyond 1.4.7.6
I recently bought some SG300-10 switches which were still at v1 firmware and so far I have been able to successfully upgrade the firmware to version 1.4.7.6. I have tried upgrading to all of the versions beyond 1.4.7.6, but after uploading the file ...
Can we stack c2960s switches with C2960X-STACK= module (Catalyst 2960-X FlexStack Plus Stacking Module optional)??
Hello.In short, how do I configure the 2960x_SWITCH1 so that I can SSH into it?SSH services are up.My ethernet cable connects to access ports with the same "vlan 77" on 2960x_SWITCH1 and 9300_SWITCHSTACK1.On 2960x_SWITCH1 is configured interface vlan...
Nexus 5672UP connecting to the Fabric Extender , the Nexus 2k , shows that the Port Channel i setup is down hence no connectivity to my Servers . How Do I turn it up? My Nexus 5k configs are as follows with several show commands; =~=~=~=~=~=~=~=~=~...
Hi everyone, I am working with cisco switch WS-C3750X-24,On my running configuration there is nothing under VTY and console line it like this:line con 0line vty 5 15there is not any information regarding "transport input SSH or telnet."But i am getti...
I have been facing this issue and any help is appreciated.My corporate laptops (running windows 10, of different vendors) doesnt receive the EAP request identity packet from the connected 9300 switch when their LAN cable is disconnected and reconnect...
Resolved! Vlan shows down/down
Looking for a little help in why a newly created Vlan shows down/down when I issue a sh ip int brief command.My setup is an AP with two SSIDs on two different Vlans (4 and 7). Traffic flows properly across Vlan 4, but Vlan 7 shows it is in a down sta...
