HiGuru's who have implemented Wireless LAN Controller, any recommendation or watchouts based on experience.
HiGuru's who have implemented Wireless LAN Controller, any recommendation or watchouts based on experience.
Getting this as a 2851 router boots up . The register is at 0x2102 and the config was originally wiped using a write erase . I know its a command but can't seem to find what i need .%Error opening tftp://255.255.255.255/network-confg (Timed out)
When trying to configure "mls qos trust dscp" on the Gig-interfaces on a Sup720-10G in virtual mode I get the following error message:" HWIF-QOS: QoS configs are not allowed on VSL Portgroup."As far as I know only the 10G-int can be part of the VSL. ...
Hi,I m trying to connect 3com switch to cisco switch 3560 with sfp (Fiber). But interfaces not cumming up, can u pls suggest me if i need to use any converter in between this one.Regards,Sunish
Is it ever possible to assign loopback addresses on Cisco Switches. Or are they only configurable on routers?ThanksKevin
I have an issue where the QOS on the 3560 is not working or reporting correctly. The setup is 1) Remote site 2811 with Metro Ethernet Handoff. (Access lists contain standard voice, voice signaling and video ports and ip addresses and these access li...
Hi, kindly guide me will I be able to achive the application fail over and load balancing running on the linux servers using the Cisco load balancer 7604.thanks in adavance,Sanjeev.
Please suggest a IOS with ssh feature for WS-C3560-48PS
Is there a mib that contains queue information (depth & drops) per COS to queue mapping. This IOS 12.2(33)SXH4 command provides that info (show queueing interface gig 4/43) but I'd like to poll via SNMP if possible. Thxs.
Can you suggest a software which can automate the backup of multiple Cisco routers/switches? This is most useful especially when you have a lot (50+) Cisco devices.Thanks.Best,Tony
I have a port configured as follows:-test01#test01#sh run int fa0/10Building configuration...Current configuration : 217 bytes!interface FastEthernet0/10 description <user ports> switchport access vlan 10 switchport mode access switchport nonegotiate...
Hi allI log into my router via ssh and i use a username and password, level 15, how do I login so the router goes straight to aneble mode ?
Hi,We bought a Cisco SGE2000P 24Port switch and 10 WAP4410N access points. Our intent is to provide a secure network to our LAN, and a guest network to the Internet.We are thinking 3 VLANs would be best for this: VLAN 100 connected to the LAN, VLA...
I have a bunch of VLANs configured on my 6513 FWSM. I wanted all my VLANs to be on there but just found out a requirement to run IRDP. Since IRDP can only be run on a router interface, I had to take this VLAN off the FWSM and put it on the MSFC.How...
Dear all,I have some strange issue inside my LAN, and it summarizes as following:Some inside PCs can access outside url: http://www.egypt.hsbc.com and some other PCs can't open this same url.Appreciate for your help.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2025 03:01 AM | ||
04-23-2025 06:26 AM | ||
04-23-2025 06:18 AM | ||
04-19-2025 09:40 AM | ||
04-15-2025 04:52 AM |
User | Count |
---|---|
7 | |
7 | |
6 | |
4 | |
3 |