Hi,Can anybody please let me know wht this module is used for o a cisco 65000 router.Mod Ports Card Type Model--- ----- -------------------------------------- -------------- 1 4 CEF720 4 port 10-Gigabit Ethernet ...
Hi,Can anybody please let me know wht this module is used for o a cisco 65000 router.Mod Ports Card Type Model--- ----- -------------------------------------- -------------- 1 4 CEF720 4 port 10-Gigabit Ethernet ...
Hi,Can anybody please let me know wht this module is used for o a cisco 65000 router.Mod Ports Card Type Model--- ----- -------------------------------------- -------------- 1 4 CEF720 4 port 10-Gigabit Ethernet ...
We have a WS-C3560-8PC. we have a 100 mb Gbic in G0/1. these 100mb GBICS default to half duplex when inserted. on the 24 and 48 port 3560 I can just go into the CLI and force the port to full duplex. for some reason that is not an option on this 8 po...
hi every body.I have some questions about nat.Let say we have two valid ip addresses , assigned by my isp which are as follows:199.199.199.1/24198.198.198.1/24I assigned the 199.199.199.1/24 to f0 of Router i.e Router F0--------internetI assigned ...
Has anybody connected a Fiber Channel SAN to the SFP port of a 3560?I have only connected Cisco switches to the SFP ports but am assuming it should work. I have tried both SX and LH SFP because the distance is short. The Cisco sees the SFP but won'...
Setup 6509-E w/ Dual Sup-7202 Line Cards - 6748s w/ DFC installedAssume that the CEF tables are synchronized between the DFC and the Supervisors and that NSF and SSO are both enabled. Question: Both Supervisors Fail - How long could the DFC CEF table...
Need some help determining what I'm seeing. I have a 3750 stack with many etherchannels. When I do a 'sho etherchannel sum' I see port channels 1-9 with a protocol of LACP, but the remaining etherchannels don't list LACP...just a -.Is this telling me...
I am currently running a 3550 with System image file:"flash:c3550-i5q3l2-mz.121-9.EA1c/c3550-i5q3l2-mz.121-9.EA1c.bin"cisco WS-C3550-12G (PowerPC) processor (revision B0) with 65526K/8192Ki would like to upgrade to the following IOS to enable BGP. Ca...
Hi,We have a 6509 core with 8 stacks of 9*3750PS. We want to use eem on the core to turn off the ports on the 3750's outside office hours(green-it initiative).Is this possible? If so do have a link to scripts we could use?The core runs s3223_rp Softw...
Hey guys i am back again for a little assistance. keeping this briefcurrently we have a dsl modem connecting to a linksys (p.o.s. router) then connecting to a dhcp server, which then hands out ip address's.The linksys router is slowly dieing, and i ...
Sorry if there's a thread on this already...I tried looking. I have an imaging server set up on its own VLAN using a 2950 switch but I cannot get the images to multicast to the clients. I also have trouble with DHCP requests going through on some of ...
I am sure this question has been answered before but for eFSU to work with an SSO enabled supervisor, there is a requirement that the line cards must have 512MB of memory installed to preload the software image via "preloading" during the ISSU proces...
I know that there are procedures to upgrade the IOS on redundant Supervisor modules for the Catalyst 4507. However, can you upgrade the physical hardware with High Availability?For example, right now I have a chassis with two Sup II+ supervisors. C...
Hi every body.I have few questions about ospf.I want to recap what i have learned from my post on net pro and book for easy reference.1) If a same router is running say two ospf processes say ospf 1 ,ospf 2, there will be two link state data bases fo...
I have switch-1 and switch-2. Switch-1 has vlans 10, 20, 30, and 40 on it. Switch-2 have vlan 110, 120, 130, and 140 on it.Each vlan is associated with its own /28 subnet. How do I route between the two switches? Do I need to create an interface V...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-16-2024 12:15 PM | ||
10-15-2024 03:13 AM | ||
10-14-2024 02:50 AM | ||
10-09-2024 11:22 AM | ||
10-08-2024 08:34 PM |
User | Count |
---|---|
9 | |
7 | |
6 | |
5 | |
5 |