Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

6445555555555555655544544445555565555554555554555555655555555555554455 0793443325312433203436987770357714431356805108824102224232452394739650100 90 80 70 60 * * * * **** * * * * * * * * * 50 ************...

mahesh18 by Level 6
  • 351 Views
  • 2 replies
  • 0 Helpful votes

Hi guys I hope some of you may be able to assist me here.Probably a simple question?I have 2 vlans 192.168.1.0 and 10.0.2.0. The 10.0.2.0 vlan is the DMZ with a web server hostting for a few freinds. Everything works just fine the server hosts multi...

wynneit by Level 1
  • 689 Views
  • 4 replies
  • 0 Helpful votes

I need to update the IOS on my 4506. Its currently running 122-20.EWA4.bin I see a couple of files out there but I want to make sure I get the right one, what file should I be getting for this switch?

lethian12 by Level 1
  • 515 Views
  • 4 replies
  • 0 Helpful votes

Hii Freinds, Facing some strange problem with Ether-Channel. We have two cisco 4507 switches placed remote to each other (i.e not at same place), connected with two parallel simataneous links(on gig ports) on which L2 etherchannel is running. ...

cisco.net by Level 1
  • 449 Views
  • 8 replies
  • 0 Helpful votes

Hi Cisco,Im trying to route an internal network to our back wireless WAN link.On our 3825 router, we have 2x physical interface (WAN/LAN). The backup wireless is connected to our switch stack on the LAN and I have created a sub-interface on the route...

Hi,we have a problem with two catalyst switches WS-C3560G-48PS. They were working for one year with no problem but from last week they are "freezing" ... no ping, all communication is stopped.In this state all port that were communicating, are solid ...

I have a Cisco 7206 that has EIGRP configued as well as Multicast. Every once in a while I see this error in the log: Apr 20 07:06:16.415 EDT: %PIM-5-NBRCHG: neighbor 10.0.0.1 DOWN on interface GigabitEthernet0/1 non DR Apr 20 07:06:29.843 EDT: %PIM-...

mortonjes by Level 1
  • 1498 Views
  • 2 replies
  • 0 Helpful votes

HiI had a switch go down recently. In replacing said switch i dropped the config onto the replacement, copied running config to start and reloaded.However, when it had booted back up, i was unable to connect back onto the switch via the console cable...

lee.foley by Level 1
  • 8706 Views
  • 3 replies
  • 0 Helpful votes

I currently have a 2960 switch configured with 2 VLANs. VLAN 1 and VLAN 104. Each VLAN has it's own separate DHCP server serving addresses for it's VLAN. I was under the impression that the DHCP broadcast would not travel between VLANs, however it ap...

dohogue by Level 1
  • 643 Views
  • 5 replies
  • 0 Helpful votes

Hi allI want to setup hsrp on my dist switchesshould I put the timers to subseconds for example: standby 1 timers msec 200 msec 1000 ?Also, can I use the same standyby group for each vlanso vlan 1standby 1 ip x.x.x.xvlan 2 standby 1 ip x.x.x.x etc ?...

Hi there,this discussion (to EASY STORY) is supossed to :1) get an confirmation, if the behaviour is bug or normal. If normal, what can I do to accomplish my task.2) let someone with latest IOS train to test it, or perhaps to open a case if this is i...

Hi,one of our sites has 2 switches acting as core with hsrp enabled.Suddenly, last 2 weeks i have noticed that there are some strange messages on the 2nd switch, which is the standby one.These messages dont appear on primary switch.I have attached th...

suthomas1 by Level 6
  • 611 Views
  • 6 replies
  • 0 Helpful votes

I want to know whether we can install a 10G linecard on the supervisor slot of a catalyst 6509E switch...As all the other slots are utilized with different linecards and service modules we want to utilize the supervisor slot which is free....can anyo...

rv_viji by Level 1
  • 475 Views
  • 2 replies
  • 0 Helpful votes

HiUsing CBWFQ with access-lists to match traffic assigned to classes. If access-lists are not very specific, what happens to traffic that is matched by 2 or more access-lists i.e. traffic could be put multiple classes?What is the process for the rou...

peterbe by Level 1
  • 454 Views
  • 2 replies
  • 0 Helpful votes