Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Let me start by saying I have read A LOT - everything I could find on Cisco VLANs, and I still can't figure out how this works.I have inhereted an environment of a bunch of Cisco APs Aironet 1130's, and a 3750 into which these APs plug in, and also a...
Can I use teh compact flash from one router to configure another? They are both the same make and model.
is the nvram in NPE-400 or on the I/O controller in 7200 Vxr router
Hi all, If I simply plug in my stack cables to my switches, will they work as one stack without any config?also what is the minimal config i need to put on for stacking,how would I assign an IP to the stack ?
I am new to the VLANS , so i would like to have suggestions from you people .I have a 10 MB Internet >> connected to Firewall >> connected to L3 Switch >> There are about 40 L2 switches beneath this L3 Switch with no STP as the physical design i...
Hello all,I would like to know if there is a protocol that handles packet loss failover for Gig-E Interfaces on Routers/switches and PIXes. Reason for this is that if a link does go bad with packet loss of > 2%, to make it swap to failover interface...
Resolved! Upgrading IOS
Hello! I'm just starting to work with Cisco switches in my IT career. I have an old Catalyst 2916XL M switch that I'm using to learn about IOS. I received this switch with IOS 11.2, but I'd like to get it up to 12. I'm snagged a little bit, I'm hopin...
Hi all, by default are all messages logged to the console screen, if I want the same info displayed on telnet, do I just type terminal monitor ?
Resolved! Updated Cisco Catalyst Switch Guide ?
The latest one I have / can find is from Summer 2007 / v3. Link: http://www.cisco.com/en/US/prod/switches/ps5718/ps708/networking_solutions_products_genericcontent0900aecd805f0955.pdfHowever, a few things have changed since then, and for example, the...
Dear Pro.I need some clarification about Bridge, Route & Gateway as a Hardware Secondly what is the meaning by bridging the vlans and routing the vlans.ThanksBhargav
Hii Guys, I have to configure Ether-Channel between two links with different banwidth capacity i.e 10 Mb and 18 Mb. Guess it should work,but have bit confusion that what would happen if low bandwidth link i.e 10 Mb will utilised peak. Is there ...
Hi, i can see the below logs in our router, i have checked the interface, there is no CRC, reliability is also fine, but there is slight increase in input errors for every refresh, Tried searching in cisco errror decoder for %ENTITY_ALARM-6-INFO, i...
Hi all, is it simple to set up an access list for traffic entering a vlan, would I just do an acl in to the vlan I want to stop traffic to, Would I apply this to the vlan interface ?
Hi all, I wonder what is a "forward metric"SG1#sh ip route 100.1.13.0Routing entry for 100.1.13.0/24 Known via "ospf 10", distance 110, metric 20, type extern 2, forward metric 2 Last update from 100.1.7.9 on FastEthernet5/1/0, 1w2d ago Routing De...
We've had a problem on our network recently with trunk ports error disabling on our switch stacks with the following error.45w5d: %ETHCNTR-3-LOOP_BACK_DETECTED: Keepalive packet loop-back detected on GigabitEthernet0/2.45w5d: %PM-4-ERR_DISABLE: loopb...
