When I power up my Catalyst 3550 switch, it boots up and shows "switch:" prompt. and it takes no command afterwards. I wonder what command prompt is "switch:". Please help.
When I power up my Catalyst 3550 switch, it boots up and shows "switch:" prompt. and it takes no command afterwards. I wonder what command prompt is "switch:". Please help.
Hi,I am looking for a link or links that show the relationship betweek logging severity levels and log messages? I want to find out what log messages are related to what severity level. rgds,
We have some security requirements to disable TFTP on certain routers and switches. What is the best (easiest) way to accomplish this? Looking at NO SERVICE CONFIG command, but not sure what all will result from this. Thanks for any suggestions
While trying to upgrade an image on a 3750 the atchive/download crashed causing the image to corrupt. Now the switch boots up in to "switch :". The flash has been formatted. I would like to know if I can load andrun image on it to get it to boot up? ...
Hi,What 3560/3750 CLI command will set priority of an RPS 2300 power system?Best regards, Peter
We have two non-Cisco, redundant firewalls at our office. Also we have two WAN ISP's. What type of Cisco switches would be sufficient to drop in front of the firewalls? We would only need 8 ports max, and all of them doing 100mbps is fine. Lastly...
So from other testing and my understanding if i do this:line vty 0 15rotary 5then i should be able to telnet to this device on port 3005.I have done this on routers before, and when i tried it on a 2 differnt 6509's i could not establish a connection...
Wondering if you've encountered an issue with Cisco Network Assistant v5.4. With the previous version(5.3) I could see and modify all my cisco switches(<40) but after upgrading to 5.4 I only have access to the WS-2950 and the WS-4507R models. I can't...
I have a 3550 (c3550-ipservicesk9-mz.122-35.SE5.bin), an ME3400 (me340x-metroaccess-mz.122-40.SE.bin) and two MRV 912 switches. All three support MST, which (by all indications) I think I have setup correctly.- 3550 F0/1 connects to 3400 F0/1- 3550 ...
Hello,I would like to know the permitted non operating (storage) altitude of the router 2811 and the Catalyst C6500-E.Is it possible to tell me which document I can download (or send it to me) so that I formally show the evidence to my customer ?Than...
Hi,Can anyone explain then following output.I have searched the command reference and configuration guide but they do not explain the five coloums showing packets. Are these tansmits, drops, queues.ThanksAnthonysh mls qos interface f0/13 statisticsFa...
Hi every body! I was reading about the pix 501 and its features. One of the features, is firewall by nat. Without upgrate, pix 501 can perform nat for only 10 devices. i understand that this is end-of -sale device. But before that, why would an engin...
Dear All,I have cisco 2950 C24 Switch which has some problem and and stopped at switch:i had tried after rebooing but the same problem is there.I have attached the capture fle for your refferencce .......Pls help me to resolve it .....Dipesh P
Hi,When I run the command below I get no statistics. Can anyone tell me if I need to configure the switch to enable this (enable) sh qos statistics 5/1Tx port type of port 5/1 : 1p2q2tQ3T1 statistics are included in Q2T2.Q# Threshold# Packets ...
Dear Friends,I have setup PBR on a 3560 (SW Version : 12.2(40)SE Advanced IP Services). The config is as follows:route-map mymap permit 10match ip address <access-list>set ip next hop 172.21.11.1 172.21.11.2int g0/25ip policy route-map mymapMy requir...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-03-2024 09:19 AM | ||
09-03-2024 06:59 AM | ||
09-03-2024 12:56 AM | ||
08-28-2024 02:25 AM |
User | Count |
---|---|
8 | |
6 | |
6 | |
5 | |
5 |