Hi all, on my cisco asa, if I want to clear an access list would i do clear configure access-list test etc? or can i do a no access-list test?are most commands no removed via the clear config command?
Hi all, on my cisco asa, if I want to clear an access list would i do clear configure access-list test etc? or can i do a no access-list test?are most commands no removed via the clear config command?
Can anyone tell me what software can recieve the qos statistics output data and display some useful information? I assume its something like ntop?Thanks
Hi, Would you please tell me how I could limit my 2960 interfaces to 128kbps? Best regards. Yasaman
Is there any ethernet module for the 6500 that can provide the 18.5W POE required by the Aironet 1252 802.11n AP?
Hi everyone,Suppose that a router is connected to two switches(switch A and switch B).SwitchA is connected to 2 pcs and a server.SwitchB is connected to 1 pc and 1 server.When i didn't configure vlans on switches PDUs of pcs of switchA succesfully re...
Hi,I am planning to connect a edge switch direct to our core switch.What I have currently is a âprimary coreâ and âsecondary coreâ etherchannel together and both are configure with lower bridge priority (24577).My question are:1. If I have to...
Folks, I have a FR switch with is configured as full mesh. I have 3 routers connected as hub ann spoke. I have disabled inverse arp and point to only the hub at the spokes to reach each other, still when i type show frame relay PVC it shows me ...
I'm trying to break up a /24 subnet for one of my sites in order to create VLANs. I want to break up 192.168.100.0/24 like this:192.168.100.1/26 (for 62 hosts)192.168.100.65/25 (for 126 hosts)I know there are portions of the subnet left over but I d...
Hello,I got a strange issue with a trunking problem. I have a dedicated 100mb cross-connect between two co-location facilities.Here are the configs:Switch_2950: Int f0/1switchport access trunkswitchport mode nongegotiatespeed 100duplex fullno cdp ena...
HiI have stacked 2 switches 3750 one is master and another is member. Now i have configured this stack switch as DHCP server. My problem is when the master switch goes down and comes up then the DHCP service is stopped. If i connect any new PC to swi...
Hi all,i have to sites connected through serial link.both are up.but ping is not allowed.how can i check in access list that ICMPis blocked.fdcb-habshan#sh ip int briefInterface IP-Address OK? Method Status Prot ...
Hi all, can layer 2 switches read both the cos tag and the dscp tag and apply policy to them? also do they have the ability to mark both the 802.1p and dscp value ?
Hey Guys, got a silly question here.I'm trying to work out a few vlans and to route each other on a centralised L3 switch.Do I need to configured vlan trunking in order to make the intervlan work?I had a couple of L2 switches which are connecting bac...
Can you run GLBP on a PIX firewall?Can you run GLBP on a 3750? ( I dont think so)ThanksVictor
I just purchased a 871 (non-wireless) and during the intial setup I couldnt get the 3 port up. All out of options I created a Vlan with all the ports inside, gave it an ip address and brought it up. when I connected a straight through cable from the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-30-2025 10:17 AM | ||
05-27-2025 03:30 AM | ||
05-27-2025 12:59 AM | ||
05-23-2025 10:30 AM | ||
05-15-2025 09:37 PM |
User | Count |
---|---|
9 | |
8 | |
5 | |
4 | |
3 |