Switching

Hello all,Apologies in advance if this is in the wrong forum.I have acquired a 2950 switch upon which to practice. I also have a cisco router that I can access and configure just fine, but am having problems accessing the switch via the console.It ap...

I've upgraded my 6500 to 12.2(33)SXH and since then I'm experimenting some issues:the switch crashes after some weeks and reboots automatically.I'm monitoring the memory and noticed a serious memory leak.Has some one already seen this issue?

I've got these 2960s and I'm trying to upgrade the code, I copy tftp the image but when I try to set the boot statement I get the following error and as a result switch never boots with the new image:Switch(config)#boot system flash:c2960-lanbasek9-m...

I'm trying to use per-packet load sharing on two E1 serial links, but it seems that does not work with FTP.. When I ping I can see the count on the other the two interfaces but when I tryo to FTP, I see the hits on one serial only.. Am I doing someth...

Hi,I've got some questions about used routers. If I buy a used 1841-SEC/K9 with version 12.4(8), what would be the proper (and least expensive) way to obtain the latest software, the vpn clients, and/or a Smartnet service contract.Thanks!

Hello all,If I apply a 10 Mbps aggregate policer to one VLAN which belongs to two ports on one switch for inbound traffic, will the inbound traffic on the two different ports for the same VLAN will share the 10 Mbps bandwidth or under each port the ...

Version 12.2(25)SEE4IPSERVICESaccess-list 100 permit ip 10.23.10.0 0.0.0.255 anyroute-map rm permit 10 match ip address 100 set ip next-hop 10.23.7.1!c3750-01-core#conf termEnter configuration commands, one per line. End with CNTL/Z.c3750-01-core(co...

I have a strange issue. Our 6509/sup720 had some performance issues. Traffic traversing the switch was slow, ftp rates were horrible, etc. It didnt matter what servers and what ports were involved. I verified there were NO cabling/interface type i...

Hello! Plz Experts;convert these entry to a simple Vlan-access-list instead of whole lines10xsip access-list extended ACL-ACL permit tcp 192.168.128.0 0.0.127.255 10.10.100.0 0.0.0.255 eq 80 permit tcp 192.168.64.0 0.0.63.255 10.10.100.0 0.0.0.255 eq...

Hello,I have a 3Gb layer-2 ether-channel between (2) 6509s running IOS. It currently runs at about 2.5Gb during peak hours.What I've noticed though is that utilization on the individual links is not equal. 2 run at about 95% while the third runs at 8...

I'm trying to pass routes learned from RIP on an external NIC on my PIX through to my internal network, but to also filter those routes that are passed through on an address by address basis.For example, on the outside of my network, I have a vendor ...

hii have this question:enable eigrp 90 on ur network and redistributer it to OSPF With a metric of 150 and Tag 20.how would i configure this?my ospf process is 1..what about if i redistibute it like this without metric and tagrouter ospf 1redistibute...

Hello, i've got three questions concering the"show ip eigrp topology" command.Sample Output:--------------P 172.16.90.0 255.255.255.0, 2 successors, FD is 0 via 172.16.80.28 (46251776/46226176), Ethernet0 via 172.16.81.28 (46251776/46226176), Ether...