Switching

Hi all!Please i need to purchase a switch that has the following functionalities .(a) Prevent broadcast issues (b) Configurable for VLAN(c) With securities fixtures (d) Scalibility for future needs Please what is your advice .Should i go f...

Hi All,I have 2 Catalyst 4506 switch and I upgraded our server segment speed from 100 mgps to 1000 mbps for 30 ports in the catalyst 4506 switch.No other config was changed.Now I am not able to access the both switch thru telnet, but access thru cons...

hi can anybody please check this configuration out and verify that nat and PBR are properly configured?also if the static entryip route 100.0.0.0 255.255.252.0 FastEthernet0/0is realy necessary...thanks

Hi all !!I'd like to config private vlan on Cisco Switch module 3020 ( for HP Chassis ). But IOS do not support (cbs30x0-lanbase-mz.122-25.SEF1/cbs30x0-lanbase-mz.122-25.SEF1.bin ). Please tell me which IOS version can support this feature.Thanks a l...

I would appreciate if any body would let me know the advantages of using VRRP over HSRP in a cisco environment (Cisco Switch & router).My colleagues are explaining me to use VRRP over HSRP but I am trying ro explain them to use HSRP.I would appreciat...

Hi NetPro,does anyone can share with me what does this mean ? Aug 13 12:26:19.781: %C6KENV-SP-4-PSFANFAILED: the fan in power supply 1 has failedAug 13 12:26:21.389: %C6KPWR-SP-4-PSFAIL: power supply 1 output failed.Aug 13 12:26:21.393: %C6KPWR-SP-4-...

HelloWe currently have 3 vlans setup on out 4507 switch they are 10.1.1.0, 10.1.101.0 and 10.1.102.0. we have been told by HQ that we need to migrate all addresses to 10.84.0.0 range. How can i do this in stages without interupting the network. Do...

I just installed Windows 2003 R2 on HP DL380 G5. After I create NIC teaming, the server receives the following Event ID 434. I have called the HP tech support and upgrade all BIOS and drivers. I also upgraded the Windows SP1 and 2. I have changed the...

Hi forum,Just collecting opinions, Is it good to isolate printer into a single VLANs or isolate the printer into departmental VLANs. If there is only a single printer server/spooler, it is learned that print job will be spool on the server before sen...

I am trying to configure a HWIC-1GE-SFP on a 2821 as a 802.1q trunk to connect to a 3508 switch.If i try a show int gig x/x/x I get "gig x/x/x is not a switchable port"I read the documentation that these modules do support dot1q VLAN's so what am I m...

We just purchased 4 CE switches and I'm trying to configure the 1st one. When I select Static and give it an IP address of 192.168.1.50, and select submit, it kicks back an error of "192.0.0.0 is (well, basically it doesn't like it.) but if I put in...

Please see the following output:CPU utilization for five seconds: 74.88% one minute: 76.24% five minutes: 76.05%PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process--- ----------- --------...

I have just upgraded 3 4507R's running Sup V's. I have noticed the CPU utilization is abnormally high. I have 1 switch that has no users on it currently and it's sitting at 17% utilization. The other are at 24% when they are normally at 11% before th...

I have a 3560, typical setup with voice and data interface GigabitEthernet0/6 switchport access vlan 200 switchport mode access switchport voice vlan 100 spanning-tree portfastVlan 200 has an interface 192.168.2.1Vlan 100 has an interface 192.168.1...