Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Can OSPF establish a neighbor on a secondary IP address on an interface?Thanks in advance
Resolved! Redistribution and distribution lists
If you are using redistribution of OSPF into EIGRP and also redistribtion of static routes. If you have a distribution-list configured for in is the distribution-list valid for both redistributions? Also can you have distribution-lists in and out.
Hi all..I have two new 4503 cat`s with Sup II+TS 10/100/1000BaseT supervisor module in.. This is set up in slot 1 of the chassie... the modul have 12 GE ports (RJ45) and 8 SFP ports..I am not able to get the interfaces in up mode. I have put in a RJ4...
Resolved! 2503 password recovery
hi, how to password recovery for router 2503 which is IOS 11.0?Regards,Samuel
My router died this weekend and when it came back up I received this message: System returned to ROM by bus error at PC 0x400BB448, address 0xB0D0A:22 UTC Sun Oct 22 2006System image file is "flash:c2800nm-advipservicesk9-mz.124-7.bin". Can anyone ...
Resolved! Communication between 2 VTP domains
Hello there!Is it possible to let 2 vtp domains communicate with each other?We have one network devided over 40 locations in one city. in half of the network some vlans excist and in the other half other vlans excist. There's no need that the whole n...
Hi,I have a 3750 that within the config has (on gig1/0/2) "switchport autostate exclude". Checking with the command "show int switchport" does indeed show "Autostate mode exclude". Given that this command does not appear to be support on this switch ...
Is there a minimum IOS requirement for configuring router-on-a-stick for a router or switch? I've configured it before on other gear, but for some reason I've been having trouble setting it up for this switch. I have two vlans (native with no IP, 2...
Hi, can you help me on this ?I am following the configuration from the link below.From workstation1, I can ping the default the router successfully. However, I can't ping anything from workstation2. My goal is to ping from workstation1 to workstation...
Hi, I currently have 3 6500's configured using HSRP all each with a MSFC so there is 3 Routers in the HSRP Group.The added attachment shows the 3 routers and there configurations and that Router 3 is the active HSRP Router. My issues are after reco...
I currently use SNMP to monitor all of our switches. I would also like to add the ability to be notified when a switch has been rebooted. Does anyone know the OID +description that gets incremented after a switch reboot ? All of our switches are 3548...
I have a Cisco 2621XM Router running IOS version 12.3(16). The router has 2 ethernet interfaces. 1 is connected to a cable modem and the other is connected to the internal LAN switch. I am trying to setup the router to forward packets coming in on...
Since upgrading our core 6509 to a brand new 6509 sup720 we have noticed some strange Receive Errors on a number of interfaces. These interfaces all share common characteristics - they are all access ports, connecting to identical switches.The errors...
I'm setting up a stack of 3750 switches with four ports grouped into two etherchannel groups to uplink to a pair of 6509 core switches. The core switches have vlan interfaces that are load balanced with HSRP. The 3750's will have a number of servers ...
Hi all, when people say firewalls can check down to application level, does this mean by port number or by type of application, as I thought port numbers are generally related to an application, in this case wont an access list do the same job ?
