Hi all, I have a cbs350-8p-e-2g with version 3.4.0.17, every time to reload it will show below message but I didn't make any configuration changes. Is it a bug ?"You haven't saved your changes. Are you sure you want to continue ?"
hi all,all switches are running rapid-PVST. a VSS formed by 2x 6506-E connects to access switches via port-channel, no redundant physical link, it is like:VSS <---port_channel--->access_switchsince some of the access port is not explicitly configured...
Hi Guys n Gals,I am having a bit of trouble with an assignment I am doing in packet tracer.I don't have the files handy until the eve, so will send pics/files later if required.My problem is that I have an access router connected to 3 separate cluste...
hi all,Thanks for your reply!physical topology is very simple: core switch stack (2x WS-C6506-E) connects to access switch via port-channel, no more redundant link. I see lots of topology change logged from core switch, for example:Number of topology...
Hello! I was wondering if I could get advice/input when it comes to QoS at the distribution layer of a network topology. Here's a high-level of our network topology.Soon to deploy two Cisco C9500k in a Stackwise HA configuration. It will have about 1...
When I connect to the switch(2960x) for the first time with the console, I get the following error and I cannot enter any commandError opening tftp://IP/ios name.bin (Time outThank you for helping me
Work on a Mac for my lab exercise, I have followed all the instructions for an SSH connection, including configuring line VTY 0 4I have read all the posts on here and nothing seems to fix the error" connection closed by foreign host".
So basically I have this problem I have setted policies for Dot1x and MAB on both Cisco IOL L3 (version 15) and Cisco ISE (RADIUS Server) but client do authentificate only with the default method which is MAB (I did set an order for methods on Switch...
Trying to authenticate I have this error as shown, can anyone help me!*May 11 12:38:20.482: %RADIUS-4-RADIUS_DEAD: RADIUS server 192.168.100.3:1812,18 13 is not responding.*May 11 12:38:20.482: %RADIUS-4-RADIUS_ALIVE: RADIUS server 192.168.100.3:1812...
HelloAfter I have setted every policy on the switch and everything is working fine through an ISE authentification via dot1x, now server cannot reach its gateway in order to give IP DHCP addresses to the hosts on VLANs!Can anyone help me please
Hello All, I have a question, I built the following DHCP pool and ACL on the Cisco core. When the ACL is on the computer doesn't able to get IP address from DHCP but when I turn off the ACL it works perfectly fine. So here is the question when comput...
Good morning
I am facing the following problem on a customer location with main and backup router. cisco ISR4331/K9
We see constant incoming IHQ packets on the WAN Interfaces on both routers. At the same time there is almost no traffic on the WAN Int...
Trying to authenticate I have this error as shown, can anyone help me!*May 11 12:38:20.482: %RADIUS-4-RADIUS_DEAD: RADIUS server 192.168.100.3:1812,18 13 is not responding.*May 11 12:38:20.482: %RADIUS-4-RADIUS_ALIVE: RADIUS server 192.168.100.3:1812...
Hi, i have problem of synced betewin my 2 switchs nexus 7.0.3.i7.3I use feature BGP, LACP and VRRP (also VPC etc..)But it's impossible of configure correctly the protocolI have many errors :One : In log :%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 9-1...
