Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...

IMG_1447.jpeg IMG_1448.jpeg IMG_1446.jpeg
amnavada by • Cisco Employee
  • 18249 Views
  • 36 replies
  • 2 Helpful votes

Good day pros,Two week a go, was trying to upgrade  Cisco C9200 (STACK2) switch from IOS cat9k_lite_iosxe.17.12.06.SPA.bin to cat9k_lite_iosxe.17.12.08.SPA.bin. It was successfully uploaded and I changed the boot variable. (As I did upgraded many sta...

Is there a way to check basic Meraki switch hardware health metrics? Unit temperature, fan speeds, any internal failures?The "device health" tab seems to only expose some hardware statuses (CPU: good / poor; memory: good / poor, etc.) - but I see no ...

kindzma by • Level 4
  • 506 Views
  • 7 replies
  • 1 Helpful votes

Hi all,Yesterday I upgraded two Cisco 9500-40X switches from IOS-XE 16.6.9 to 17.18.4 and configured them in a StackWise Virtual setup.In my previous experience with the Cisco C9500-48Y4C-A, the standby switch's console port became unavailable for co...

marzi by • Level 4
  • 186 Views
  • 3 replies
  • 0 Helpful votes

Hello, our 9200 switches with code 17.9.4a receives dacl from ise and authorize clients successfully. Based on the complaints (endpoint can access to destinations that they shouldn’t as destinations not allowed in DACL) we started to see if anything ...

tungrwaga58 by • Community Member
  • 1240 Views
  • 6 replies
  • 0 Helpful votes

Can anyone explain why a burned-in MAC address might deviate from the logical numbering scheme? Typically, the MAC addresses for a switch’s ports begin with a base MAC address and increment in sequence, corresponding to the port numbers. In our case,...

Tec1do by • Community Member
  • 1798 Views
  • 28 replies
  • 2 Helpful votes

Hello, everyone! I'm new here and just have, still, a very basic knowledge of how to use Cisco Packet Tracer. I'm really trying my best to learn, but I got into this problem, and I feel like I don't know what to do anymore. Just really hoping someone...

redtamaraws_0-1737408897059.png
redtamaraws by • Community Member
  • 2211 Views
  • 5 replies
  • 0 Helpful votes

Hello i just started a QC position at my job with minimal training wanted to see if there was and emulators or thing of that nature to test ports extremely new to this working with switches for cisco would gratefully appreciate any info tips thanks.

TXFloater by • Community Member
  • 250 Views
  • 5 replies
  • 0 Helpful votes

I bought a Cisco Catalyst switch from a hamfest (amateur radio swap meet) and am trying to get it working.  I am a retired software engineer and am just looking to get this working.  I can connect to it through a serial conection and can run some ini...

I've just got an email that I passed a certification and received a CISCO ID number.The thing is I did not have a CISCO account, so I created one, but now when I go to Cert Status & Download PDF, I don't have an option to paste that CISCO ID number.I...

domnikraeys by • Community Member
  • 204 Views
  • 2 replies
  • 0 Helpful votes

Hi everyoneOur SFP-10G-ER modules aren't recognized as supported by a C9300-24S with C9300-NM-8X. According to the compatibility matrix, they should be compatible.We tried workarounds I've found for similar errors, like cold-boot the switch several t...

cjaras by • Community Member
  • 641 Views
  • 7 replies
  • 0 Helpful votes

Hi All,I've read some posts about noisy switches, but this post isn't about that issue.I'm trying to get a good idea of how loud the Meraki switch fans actually are (when operating normally).Specifically, we are looking at rolling out MS225-24P (PoE ...

ShaneMartin1 by • Community Member
  • 28141 Views
  • 15 replies
  • 1 Helpful votes

Hello switching experts! I have deployed a pair of Cat 9300 switches i.e 9300-48T-E running IOS 17.9.4. These switches are stacked. Everything is working fine. However, a strange issue is being faced i.e. switch is unable to ping its local SVI. The p...

Ismail Ilyas by • Community Member
  • 6384 Views
  • 15 replies
  • 0 Helpful votes