Hello,I see that the Telepresence Conductor does not support 8710 MCU as of now but is on the roadmap. Does anyone know when it will be supported?
Hello,I see that the Telepresence Conductor does not support 8710 MCU as of now but is on the roadmap. Does anyone know when it will be supported?
Hello,One of my customer's wants to disable the function where the camera image flips over when pointing the EX60 camera completely down. We tried turning off the flip and mirror option in the menu but the camera still does the same thing. Is it poss...
Hi, i have created several permanent conferences on MCU.Sometimes permanent conference appear as finished. Operators swear they did not finish them manualy.Also, then i put conference back, by editing its properties and checking "permanent" checkbox,...
Hi Guys,Need your inputs , one of my client wants to have VC with the their international loaction and Client wants to do on MPLS, with Private IP assigned to end point and there are multiple service provider in between , He wants to have point...
Can someone help me to understand what is the product replacing TMS/VCS kind of setup?Is it CTS-Server with CTMS? or CTS-Server with MCU?Better still, if someone has the roadmap for video products.
Hello - I have deployed Cisco TCS at one of my client's place and have issues with Multicast streaming. Streaming the multicast stream from within the server itself has low frame rate issues and when streamed from a client pc, notice high packet los...
someone can explain the vcs status on a cluster configuration?my question is if the active state must be crossed between peers?, or there must be only one active vcs on the cluster? please your help ps: vcs version 7.1peer 1 master:peer 2Thank you ve...
Hi everybody!I have 3 Tandberg Quick set c20 terminals. 1 terminal was configured 1 time, installed to a place and working fine. Other 2 were configured and worked fine too, but it was need to disconnect and then connect cameras few times - we change...
Hi all,Does anyone know if it is possible to change/adjust VCS's operating system time manually?We want to do that without NTP server and no TImezone setting.Best Regards,Kotaro Hashimoto
HelloI am new in Telepresence, and Is erach for any material that help me to design a Telepresence solution, but I faild to find a valid one. I need to know what is the Telepresence infrastructure and why should we intgegrate with CUCM?, What is the ...
Hello everyone,Recently we made a change to vcs over the network and lost network connectivity ... I have the box physically in front of me .... How should I go around changing the IP address ???Should I console into it ?. If so; what will be the com...
Dear Support Community,As you can see on the screenshot the problem with the german version of the scheduler is that the time is wrong shown, after 12:45 it shows 1:00 instead of 13:00, are you aware of this issue?kind regardschristian
HI all,On MCU software version 4.3(2.32), "Video receive bit rate optimization" and "Flow control on video errors" are automatically enabled, when MCU is in one of the HD, HD+, or Full HD modes.But our customer needs to disable "Video receive bit rat...
Hi Everyone,we have a video infrstructure in which there is a1)VCS control verX7.12)VCS expressway ver X7.13)TMS 13.2we have recently upgrated tms 13.1 to 13.2 and installed TMS provisioning extension on TMSAfter installation of provisioning extensio...
Hi,On the TC5.1 Touch Screen for C20 or EX90, is there a way to disable acces to the "Language, Camera Control & Setttings, Display Settings and Ringtone & Sound Settings"?This to avoid any problem of mis use by customers.I don't find any command in ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-27-2024 06:47 AM | ||
06-26-2024 12:54 AM | ||
06-10-2024 11:20 AM | ||
06-10-2024 11:14 AM | ||
06-10-2024 09:51 AM |