Hey Guys.. I am new to Cisco UCS and support an environment with 5108 chassis with B200 M3 blades connected with redundant fabric interconnects. These blades are configured as ESXi servers with 2 Distributed switches and 2 uplinks on each switch. M...
Hi there! I've inherited the management of a chassis, running UCS Manager 2.1(3g). Now it must be moved into a new network, new IPs, etc. So, I changed the management IP addresses of the Fabric Interconnects and the UCS Manager connects just fine, ...
Hi,We are running 4 Chassis in our enviroment with firmware 1.4 (3q) and recently we had an issue with one of the PSU (PSU2) in chassis 2 and we got it replaced and after that we are observing that 1 of the PSU in each chassis is showing as "Power Sa...
Hi All, Is it possible to do a UEFI secure boot from Flex 32GB SD card for esxi 6.5 or a Local lun is required for this as the UEFI boot parameters cannot be set. From the below article UEFI boot mode is only supported in Locla LUn or iSCSI LUN or...
Hello, we own an UCS c420 m3 and we are looking to expend the storage capacity. to do so we need to buy the now end of sales/life spare parts to add 8 hdd to it. i have been able to find the raid controller but i cannot find a reliable website that...
Hi All, Quick question: I'm currently running UCS v3.2.3 and may need to reconfigure the fiber channel switching mode. According to the UCS doc (https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Network-Mgmt/3-...
I am planning to add additional ports into the uplink vPC's on the FI's to provide more bandwidth. At the moment there is 2 interfaces in each port channel, on each FI and I'd like to increase that to 4 ports.The environment is all IP storage so I'd ...
Hello, We are preparing a setup for a new VMware environment, on CISCO UCS B200-Series (M4 and M5) and we have VIC 1340 running 1.6.0.37 driver, connected by FI (6248UP and 6332-16UP, running 3.1(3h), soon 3.2(3h)) to MDS SAN to HP 20800R2 storage. ...
Can i Use the Hyperflex without a Hypervisor? can i create VM directly to the Cluster?
Hello, we are using KVM IP Pools in UCS Manager 4. We have one IP for every Blade in the UCS. Is there any way to reduce the number of IPs in the pool and assign them like DHCP with a short lease? thanks, Andreas
Hi everyone, I have one task to mixing 64GB DIMM memory for B200 M4 and B460M4. I try to clarify if we need upgrade memory on B200M4 we need to get this memory from B460 and return to the place if need upgrade B460. I check supported memory types f...
We have 3 standalone C240-M4SX rack servers, running on Windows Server 2016 with Hyper-V installed. I am unable to get SR-IOV working on VIC1227. We have latest firmware installed (from huu 4.0.1b) and latest VIC drivers (4.0.0.3 dated 04.01.2017) SR...
I'be been banging my head on this for a while now. I've attempted all of the other solutions I've found here. Basically, I'm trying to get the server to boot ESXi off of virtual disk 0. This is what I've done so far: Booted into WebGUI for the LSI ...
Hi everone, i am new to hyperflex, i did my first deployment two days ago using the latest HX installer 3.01e and ucs version 3.2.3h and the same for B & C series and vcenter 6.5 U2. i didn't upgrade the ESXI version before cluster creation so it i...
Hi All, Our org is quite new to UCS mini. We are having a weird issue with some of our Esxi servers on B200 M4 blades dropping the Esxi management network for a minute or so periodically daily (Every other network is ok) and I think it may be down ...
.jpg "VIP Mentor"){kind=icon}
