As the title says I added more CISCO RAM to several of my UCS B200 M5 blade servers. I have 'acknowledged' the fault as suggested in the CISCO documentation. That has not cleared it. I hope I do not have to decommission these systems and commissio...
Forum Posts
I've been reading the Capacity Management in Cisco HyperFlex White Paper, and I have a couple of issues with the wording used in this paperIn particular, the use of the term "persistent tier" - in fact, I believe the term "persistent tier" should NOT...
Hello.As you see a title, I want to know whether I can shut down CIMC with ISE application running and how this operation affects ISE application.ISE is running on UCS Server.Here is the information about UCS Server and ISE version.------------------...
I am new to Hyperflex and trying to build a 3-Node Edge Cluster with HX 220c M5 servers. - Nexus 9k in place of Fiber Connects- Jumbo Frames are enabled- There are 4 VLANs created on switch as recommended, with coordinating IP structure- ESXi 6.7 U3 ...
Hopefully this is a simple question, but the C220M5 we ordered has its management port and 2 x 1/10gbe ports. i would ideally like to use these 2 x 10gbe ports for connecting to storage, but if i do so can i use the management port for both cimc and ...
Resolved! reused hardware
We are planning to upgrade blade servers from b200 m4 to m6 series.I am confused here, can we use m4 series ram,cpu,disk and vic card in m6 series?
I using B200 M2, B200 M3. each ucs using esxi version 5.5 and 6.0. this time i will upgrade Esxi 6.5(B200 M2) and 6.7(B200 M3) Do i need to upgrade the ucs firmware upgrade before upgrading the esxi version?
Good afternoon. We have UCS Mini. Connected the following way: cisco switch-- > UCS Mini-- > ESXi. It turned out that on one blade we need to install ESXi with several VLANs on one interface and drive it into the ESXi sweep. We have set up a servic...
Hi, I have a UCS domain (2.2(8e)) that I need to decommission, but I'm struggling to find the correct process or steps required on the UCS side of things to do this. Does anyone have a guide, or can point me in the right direction for this? Thank you...
Hi All, i was exporting the config files and it is stuck for almost a day now how can I break/stop the process thanks in advance
Hi Guys, We use UCSB-B200-M3 and one of the server is faulty. We replace it with the same type (refurbished). We insert in slot 6 and it is discovered in UCS Manager. But in Adapters menu, HBAs and NICs is not detected. While in DCE Interfaces, from...
As a title, I re-installed Cisco ISE with CIMC based on Installation Guide below, but some problem occured.--------------●Install Cisco ISE (Cisco Identity Services Engine Installation Guide, Release 3.0)https://www.cisco.com/c/en/us/td/docs/security...
Hello.As you see a title, I want to know the recommended firmware version of CIMC (Cisco Integrated Management Controller) and how to find where that information is posted.In addition, Cisco ISE (=Authentication server) is working under the UCS (Cisc...
I'm working with Cisco PowerTools (2.3.1.5) to take some Settings in IMC (Standalone Rackserver)I disable ipv6 over Web-Gui and record the Settings with following Cmdlet: $rackUnit = Get-ImcRackUnit -ServerId "1" $mgmtController = $rackUnit | Get-Imc...
I have been trying to deploy hyperflex from intersight and it's stuck at Unable to get the ESXi login prompt through SoL.I did not try from installer VM on-prem but wondering if anyone ran into an issue and was able to resolve it.CIMC IP is pooled an...
