Resolved! UCS FI6248 In-band management
Hi,We are currently managing our FI6248s CLI and UCS via the out-of-band managment interfaces on the FIs. Does anyone know if the FI6248s can be managed in-band over the 1/10GBe connections?Thanks,
Hi,We are currently managing our FI6248s CLI and UCS via the out-of-band managment interfaces on the FIs. Does anyone know if the FI6248s can be managed in-band over the 1/10GBe connections?Thanks,
I am facing strange problem to install ESXi to one of the blade of UCS B200 M2, after replaced both local harddisks, I am trying to install ESXi to this blade again, but after launch the KVM, seems my keyboard cannot communication with KVM, means I w...
Hi,we use B200 M2 blades with M81KR on 2.02r, running Exchange 2010 on ESXi 5.0 with PowerPath /VE 5.7, the UCS is attached via MDS to a VMAX. EMC Best Practise for EX2k10 is to use PowePath and set the HBA queue depth to 128. How?I picked the "FC Ad...
Hi,we have a pretty serious issue we are struggling to get to the bottom of. I have had a Cisco TAC case (and have just opened a netapp case) open now for coming close to a week, and we effectively have a UCS environment that is totally down. Luckily...
I've just finished reading the Best Practices in Deploying Cisco Nexus 1000V Series Switches on Cisco UCS B and C Series Cisco UCS Manager Servers document. Near the end there is a section with VSM placement options.None of the options advise placing...
Hi Guys,Just trying to get to the bottom of what this requires to fix.I understand what it''s telling me and I was just going to reset the CIMC but on investigation I am a little confused..It states in the early paragraphs that once the memory is deg...
We currently have a 2 member port-channel from each of our 6248s up to a 6500, with src-dest IP load-balancing policy set on each side. We're running into an issue where 2 particularly busy servers are getting hashed to a single PC member, and that m...
Just configure our c210 box with CIMC Manager. It work for couple of days and the connection just completely went dead on us.We setup with a static IP: 172.16.10.100,with subnet and DG.(we try to change the IP too)We can ping it and log into the CIMC...
Hi folks,I've got a problem while installing Win2008-R2 over SAN into a LUN with the VIC1240 Adapters on B200 M3 Blades. The Setup ist just not able to find any Remote Storage to install its data. When I use ESXi 5.0u1 everything works fine, the LUN ...
Q1 : one processor can not boot ? (Two processors is ok) Q2 : one processor can not detect LSI MegaRAID SAS9266-card? (Two processors is ok) Please help thanks .
We currently have CUPS 8.5.2 and want to enable the compliance feature for IM. The documentation found on Cisco's website does not explain the proper sizing of a volume/disk for the PostgreSQL database as well as maintenance procedures. If anyone k...
Hi,Importing of equipment from live UCS to Emulator fails to load and gives the following error"Server Error: code -1: 302 Found" as both http and https are enabled on the live CUCM.Thanks,Javed Koor
We are trying to determine if it is possible to install our Servers running a NICE VoIP recording Application in our Virtual environment on Cisco UCS. We have filtering TAPS installed in our network that provide as an output a copy of the RTP media s...
Is it a requirement for this to work to pull out the local disksif they are present? I am using the "Any configuration". with a local disk present.
I configured it correcly I believe. The strange thing is that there is only one iSCSi initiator pool. See attachment.so when we configure iSCSi Boot Parameters, there is just ONE IP Address Policy. I think this may be the reason th...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-18-2025 09:21 AM | ||
05-21-2025 07:35 AM | ||
05-07-2025 03:02 AM | ||
05-07-2025 12:11 AM | ||
04-30-2025 01:15 AM |