I have a server that is not responding when trying to access through GUI interface. We can ping the address and also access CLI from SSH session. I saw there was a bug found but I believe our version (3.0 (1c)) is passed the bug fix action. We did po...
Forum Posts
I can see Calvium PCI card is installed on the CIMC as below. It has 2 10G ports, and can I use them as a normal 10G port? Such as assigning IP and connect to a Cisco 3570X switch 10G port By the way, It doesn't appear on the network adapter tab. E...
Resolved! L2 on a UCS6454 with no upstream N9k
Hello, I'm trying to figure out if and how to configure 2 vNIC's on 2 different b200 blades to communicate without having to use a northbound ACI switch. Each b200 has a vNIC-a and vNIC-b Both vNIC's have been given the same random vlan 1234 Both vNI...
Hi all,I'm looking for some assistance, I'm deploying a new Hyperflex cluster for a Lab environment which is completely cut off from all normal domain services.I'm running the deployment from the appliance running on ESXI, however the validations are...
UCS C-220M3 v3.0.4e Cannot use mouse or keyboard in KVM launch for esxi config changes. I also cannot use keyboard on baremetal when booting into ESXi. Using Java 8u351, which seems to be working fine, just KVM things not working. Ideas?
I have a few B200M4 blades showing errors such as "Local disk 3 missing on server 15/3" however all the servers have 2 local disks which have the "Local Disk Configuration Policy" set to RAID1 in the Service Profile. I have acknowledged the faults b...
안녕. 이임박사 UCS B200 M5의 증상. OS 재설치를 위해서는 네트워크 부팅 과정이 필요합니다. 다만, 재부팅 후 부팅시 LSI MegaRAID 상태창이 나타나고 이후에는 커서만 깜빡일 뿐 바이오스 진입 화면은 뜨지 않는다. HA-0 Cisco FlexStorage 12G SAS 4.250.01-5047 1 호스트 어댑터에서 발견된 Virtual Drie BIOS에서 처리하는 가상 드라이브 1개 <Ctrl><R>을 눌러 Meg...
Hello,I have a problem on a UCS6248UP on which we have no more support.Following a power failure, I have the Fabric Interconnect A which has an overall Status: Inoperable. The lights are orange and all the connections to the various equipment are cut...
Resolved! UCS C460 M4 NVMe Boot
Hi,I have an C460 M4 without raid controller, it just booted from SD-Card. I added an NVMe PCIe (Intel P3500 800GB NVMe SFF SSD SSDPE2MX800G4J) in bay 5 it recognizes by the BIOS and operating system on the SD-Card, but I cannot boot from the NVMe:A...
Hi, my customer would like to manage Cisco Meeting Server 1000 M5 version (Cisco UCS C220 M5 Servers) using vCenter. My question is, which virtualization software should be installed in the server so that the server can be managed by vCenter? Is vSph...
Hi,I am looking for a script to get the wwpn, overall state, assigned, associated state of all the servers in UCSM.I can run one script for wwpn and another script for overall state, assigned, associated state. But when I try to combine both, it does...
Hi All,We have a pair of 6296UPs at one of our sites and the website on the device freezes almost every time. When you try to log into the device, you get to the page to select UCS Manager or the KVM. Clicking UCSM often doesn't load and sits on the ...
Hi,We are facing an issue where we have multiple bootable OS installed on the local LUN and the external USB key.We are trying to boot on either one of them using the appropriate boot order with a boot policy, but the server keeps booting on the same...
I've created a usb bootable drive to reimage my hyperflex C220 M5 converged node to ESXi 7.0U3. But when I go into the boot menu I don't see my connected USB drive there. I've created the bootable USB drive using rufus and I have chose the following ...
Hi all,I have an issue with the UCS server that, after swapping the HDD and rebooted, it was fine for a while that everything is in good condition, however, the following day when viewing through CIMC, we have all the HDD showing as unconfigured good...
