Ask Me Anything Event Welcome to the Cisco UCS C-Series Servers session! Whether you're setting up your first server or optimizing an existing deployment, this event is your one-stop destination for everything UCS C-Series. Our expert engineers, P...
I'm going to add memory to an existing B200 M2 blade that's associated with service profile and is in use. Do I need to do anything more than to shut down the blade/OS, pull it, add RAM, re-install, power up?Given that the blade is going back to the ...
Hi all,quite sure answer is no.....but i'll still try to make question .id ti possible to dual boot from local hard disk?I mean one profile with one OS (maybe ESX4.0) and other profile with another OS (ESX4.1)?PS: i know that i can do it with san boo...
B200-M1 blades and Menlo CNA.The SPs are using a dynamic vNIC templates with fabric A or B selected and F/O enabled.What we're witnessing is the OS will always be presented with two NIC's. Depending on which Fabric A/B the SP is set to determins whi...
I had two customers looking for this. In other blades, they have the ability to hook up to 8 NIC's to a switch and then that switch(s) can be in DMZ1, DMZ2, internal etc. So basically they are able to do physical segmentation of their vhosts on ESX ...
Dears,I have UCS 5108 and blade server 200M1 , and clariion CX3-300 , and Install Windows 2003 , HBA type is emulex .we configure the service profile to boot from the SAN , it was work mfins without any problem , but when we dissociate the service fi...
Hi,can we use a 6120 Interconnect as a FC switch, so do the usual FC zoning stuff and directly connect some FC storage to the FC expansion ports, or do we need to run the interconnect in NPV mode and connect it to a NPIV capable switch.Regards,John
I have deployed a few UCS installs and have used static wwnn and wwpn. The problem I see with using wwnn and wwpnn pools is that if you mask you Luns to a wwpn on the host and the service profile is removed there is the potential of the host getting ...
Hihow can I set My UCS 6120 Xp to 1 Gpbs speed as Uplink to my Upsteream switch I have only 1 G CLC MM GbigMY UCS is 1.2 shall I need to Upgrade the software ????could you help
I am evaluating Cisco UCS for our DC environment and New to it.I have the following Questions Operational Benefits of UCS?Operation Challenges in UCS ( Post Deployment)?Technical Challenges in deploying UCS ?If someone could answer these Questions, w...
All,We are deploying the Nexus 1010 Virtual Services Appliance for the purpose of using the Network Analysis Module (NAM). The 1010 hosts the VSM's necessary to deploy the 1000v switch in ESX. We would also like to use VN-Link in hardware whereby w...
i have ucs-c200m2 with soft raid1 on two 500G hdds. i'm trying to install windows server 2008 R2, but installation never finished. during last step "Completing Installation" server restart and after booting i get following:any suggest?! problem with...
IN UCS how can I reboot the chassis only or shut is down ???
can you privde me for basic troubleshootings steps for major fault when create Server from service proficle for vnic 0 , adapter link down ?major,F0207,49182,sys/chassis-1/blade-1/adaptor-1/host-eth-1/fault-F0207,link-down,2010-12-12T14:20:39,Adapter...
HiWe are planning to deploy UCS n our environment. The Fabric Interconnects A and B will need to connect to pair of Catalyst 4900 M switch. Whats is the best practice to connect? How should the 4900 switch be configured? Can I do port channel in UCS?...
Hi, all, I have UCS B200 M1 & M2 in one chassis . I had installation ESX 4.0 update 2 in both server . I found out virtual machine can't vmotion on both ESX servers , how can I resolve this problem ? Thanks a lot.
