I have deployed a few UCS installs and have used static wwnn and wwpn. The problem I see with using wwnn and wwpnn pools is that if you mask you Luns to a wwpn on the host and the service profile is removed there is the potential of the host getting ...
Hihow can I set My UCS 6120 Xp to 1 Gpbs speed as Uplink to my Upsteream switch I have only 1 G CLC MM GbigMY UCS is 1.2 shall I need to Upgrade the software ????could you help
I am evaluating Cisco UCS for our DC environment and New to it.I have the following Questions Operational Benefits of UCS?Operation Challenges in UCS ( Post Deployment)?Technical Challenges in deploying UCS ?If someone could answer these Questions, w...
All,We are deploying the Nexus 1010 Virtual Services Appliance for the purpose of using the Network Analysis Module (NAM). The 1010 hosts the VSM's necessary to deploy the 1000v switch in ESX. We would also like to use VN-Link in hardware whereby w...
i have ucs-c200m2 with soft raid1 on two 500G hdds. i'm trying to install windows server 2008 R2, but installation never finished. during last step "Completing Installation" server restart and after booting i get following:any suggest?! problem with...
IN UCS how can I reboot the chassis only or shut is down ???
can you privde me for basic troubleshootings steps for major fault when create Server from service proficle for vnic 0 , adapter link down ?major,F0207,49182,sys/chassis-1/blade-1/adaptor-1/host-eth-1/fault-F0207,link-down,2010-12-12T14:20:39,Adapter...
HiWe are planning to deploy UCS n our environment. The Fabric Interconnects A and B will need to connect to pair of Catalyst 4900 M switch. Whats is the best practice to connect? How should the 4900 switch be configured? Can I do port channel in UCS?...
Hi, all, I have UCS B200 M1 & M2 in one chassis . I had installation ESX 4.0 update 2 in both server . I found out virtual machine can't vmotion on both ESX servers , how can I resolve this problem ? Thanks a lot.
Hi,I am looking for some clarification on how the Palo VIC presents the vNICs, how to tell/control which vNICs map to which physical ports, and how to best configure my environment for VMWare.Hardware Summary :B250 (full width) blades with 2 Palo VIC...
when creating VSAN and provide it to uplink in UCS , does the VSAN needs to have the same ID on the production Vsan in the MDS- core fabric switchI have one two Fabric each sinngle MDS- switch and I need to connectone uplinks from one single fabric ...
I create a service profile template that boots form local disk when I create Service profile from it , it give me config fuiluer and the error was regarding the missing or no wwnp on virtulization port. I create obe VHBA fc0 and also the wwwn and www...
I'm using the instructions in the UCSM_GUI_Configuration_Guide_1_3_1.pdf to upgrade my ucs equipment. There are several questions and issues I've had.1) It says to update the firmware for the IOM's and wait till you activate the firmware on the fab...
Hi:The UCS ecosystem leverages a port aggregation solution to chassis I/O, namely, the FEX modules.The FEX modules are not fully featured switches. Nor do they possess any forwarding policy intelligence at all. Instead, the FEX modules deploy a "p...
I have a new UCS200 that I will be evaluating. I am getting errors on boot: pxe-e61 media test failure and asking to check cables. I removed the cover and all looks well. I have also tried to boot form different devices, all with the same message...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-03-2025 07:07 AM | ||
| 11-30-2025 06:22 PM | ||
| 09-23-2025 12:33 PM | ||
| 09-09-2025 06:54 AM | ||
| 09-05-2025 12:03 PM |
