Hi Folks, I tried to boot from a USB my server B series. I insert the USB into a KVM dongle an set the policy as below Local FloppyLocal CD/DVDRemote Virtual DriveCIMC Mounted CD/DVDLocal Disk but didn't work.
Forum Posts
Hello, i have question regarding Cisco UCS C220 M5 Server appliance. Is the machine able to auto boot up when power resume after a power outage? Can't find any of that settings in the BIOS. Right now, after turning off the power and then turn back on...
Hi folks,in my UCS Cluster i have four Blade servers. Two B200 M3 and two B200 M4.The M4 servers have two adapters in inventory:UCSB-MLOM-40G-03 and UCSB-VIC-M83-8P.Now my question is:Should i separate my vHBA (fc0 and fc1) on two vCONs (four are sho...
HI all,According to the example of official website curl -GET https://10.10.10.10/redfish/v1/Managers/CIMC/LogServices /SEL/Entries\?\$skip=2\&\$top=2 -u admin:admin123 --insecureThe upper example code can get top two and skipping two records of sel ...
I would like to know if it is safe to delete SSH core dump files on Cisco UCS FI as sysmgr 100% FULL (nxos)# show system inter flashMount-on 1K-blocks Used Available Use% Filesystem/var/sysmgr 2048000 2048000 0 100...
Resolved! Operating System Support
I have a Cisco UCSC-C220-M3S server with Windows server 2012 installed in it and got a request to Upgrade the OS to Windows server 2016 or 2019 .Could you please let me know if this server hardware support the OS ? Thank you in Advance .Yusuf Basha
Hi, I have a situation that we have to move one of our hyperflex nodes servers ports from 10g to 40g on same fabric interconnect (6332-16UP). Is it possible to move servers ports on hyperflex infra?Is there any impact on HX DP if we move servers port...
I'm attempting to upgrade ESXi nodes in a USCM cluster using Hyperflex Connect. Under the Upgrade navigation link, I select Upgrade. Then select ESXi, drop in the upgrade image (which validates successfully) and the vcenter credentials. It starts the...
Can C220 run ok with one failed hard disc if the other discs are ok? at what point is this a major problem, as am unable to raise an rma becuase of cotract issues till tomorrow?
I plugged the server to a power source, and after pressing the power button the server wouldn't boot.I tried to connect to the serial port to get more information and I got this screenshot:Any thoughts about how to solve this?
Hello, How do I flash a Cisco UCSC RAID SAS 2008M-8i in IT mode/use HBA passthrough? Also, can I use my existing JBOD drives with the server after I flash it in IT? I can't find any individual RAID firmware for it, and I have been advised not to use ...
During a Hyperflex Installer deployment, during the Deploy Validation phase, I'm getting this message:vCenter Reverse Proxy Port CheckvCenter reverse proxy at x.x.x.x is not reachable. Verify vCenter rhttpproxy port is open and set to 80. The springp...
Hello all, We use UCS Central extensively, and our Prod and DR domains are using the same instance for configuration management. I'm trying to think of the best way to deal with the case if our DR site could not communicate with our UCS Central in a...
Hi Guys, I have one C220 M3 server with 4 500 GB HDD CC03 and I have one of them shows moderate fault, then I decided to replae that HDD with another one, but the new one is CCO2 FW version, my question can rebuild success? or need to be in the same ...
Resolved! ucs C220-M3BE shutdown after 5 minutes
Hi, I have one server C220-M3BE CICM version 1.5(4d) I tried to rebuild one HDD and is done the HDD is Online but still have Predicted error, and I can not access with CIMC in GUI interface, always stuck during loading (Before rebuilding I was able t...
