Hi, I need some advice on what might go wrong with my tunnel I established this tunnel like 6 month ago and it was fine until now. It's IKEv1 tunnel between vMX in Azure (my nva) and some 3rd party virtual ASA device. Tunnel is up but I can reach rem...
Forum Posts
Hello.On an ASA 5525, is...#crypto ipsec ikev2 ipsec-proposal PROPOSAL-1#protocol esp encryption aes-256#protocol esp integrity sha-512...the same as...#crypto ipsec ikev2 ipsec-proposal PROPOSAL-1#crypto ipsec ikev2 transform-set VENDOR1 esp-aes-256...
Resolved! asa5506 inside nat question
let me start by saying i don't do allot of VPN work so this is a little out of my wheelhouse.the issue is:I have a VPN tunnel between my office and a vendor. they want me to nat a machine on my side to another ip so it wont conflict with their intern...
I have been trying to find documentation for configuring through FMC a site to site vpn tunnel when one network matches a network on the far side. I have a network 192.168.200.0/24 that is also routed on the second network. I am trying to NAT the 192...
Resolved! VPN via NAT
I have the following topologywith NAT-T disabled on Cisco ASA (no crypto isakmp nat-traversal 20), I got the followingI thought the VPN should fail. What did I miss here ?thanks a lot !!
We have a remote site which is behind the NAT device. We turned of NAT-Traversal with no crypto isakmp nat-traversal.Can we enable NAT-T on tunnel base instead of enabling this globally?
On my Employer supplied Macbook Pro, I'm running AnyConnect Secure Mobility Client version 4.10.03104 on macOs Monterey. I have admin privileges on this computer, but not on the VPN server. I often have about a dozen different terminals with ssh sess...
Hello, We are having issues setting up firepower anyconnect authentication with LDAP/AD. We have a realm setup with our AD servers. We can obtain users/groups from AD with it, and can authenticate into the FMC with AD credentials. However, when it...
Resolved! DVTI no ip address?
Dear experts, I've setup a DVTI with IKEv2 to get remote access into my 2901. However, the IKE session establishes, without any errors, the interface comes up, but no IP address is assigned to the Virtual-access interface. The client is a C881 runnin...
Hi, I have Firepower 1140 with Anyconnect license. VPN users are from AD (by LDAP). Everything it's ok, but when user have expired password don't connect - users see error "Inwalid user or password". When I had ASA, users when their password is expi...
Resolved! site to site vpn
Hi Guys,I have 2 routers running ospf point to point LAN--> HQ-TX <---> NV-Branch <-- LAN which is running site2site VPN and works perfectly. Now for fail overs i added an INTERNET router with new design LAN--> HQ-TX <--> INTERNET ROUTER <--> NV-Bran...
Pretty basic AnyConnect config, GroupPolicy: group-policy XXXX attributesdns-server value <DNS1> <DNS2>vpn-filter value <FILTER>vpn-tunnel-protocol ssl-client split-tunnel-policy tunnelspecifiedsplit-tunnel-network-list value <SPLIT_POLICY>default-do...
Hello, Have been using the VPN Anyconnect until a few weeks ago when authetication stopped. No changes done on the AD nor the firewall. However, i noted that the AD and LDAP group configs on the firewall populates but cannot be saved despite the "cha...
Communication issues - ikev1 vpn Cisco IOS <-> Fortigate I configured a ikev1 tunnel between Cisco IOS and Fortigate.The tunnel comes up but communication only works after a client of the remote site (cisco) initiated some traffic.As you can see in t...
Hello,one of my user have the problem listed in subject. The local IP is not the same as the VPN IP.Both files routechanges4.bin and routechanges6.bin, are not available. In another threat there is a note to delete both files from this directory: C:\...
